mypros+
Error code reference

Amana Washer Error Code F

Invalid option selected

Amana codesAmana washer codes

Invalid option selected — the selected option is not valid for the chosen cycle.

First step from the service manual

Refer to ERROR SIGNAL in Use and Care Manual supplied with washer.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F means on a Amana washer

The F error code on an Amana washer indicates that an invalid option has been selected for the currently active wash cycle. This is a control logic error generated by the main control board when it detects a conflict between the chosen cycle and one or more additional options selected by the user. The washer's control system is programmed with a defined matrix of compatible cycle and option combinations, and when a selected option falls outside the acceptable parameters for the active cycle, the F code is triggered to prevent the machine from operating under an unsupported configuration.

This error does not indicate a mechanical or electrical component failure. Instead, it points to an incompatible user input at the control panel. For example, certain spin speeds, temperature settings, or soil level options may not be available for specific cycles such as delicate, hand wash, or certain specialty cycles. The control board recognizes this conflict and halts the operation before the cycle begins, displaying the F code as a signal to the operator.

Because this error is a user input issue rather than a hardware fault, the resolution typically involves reviewing the cycle and option compatibility chart provided in the Use and Care Manual for your specific model. Clearing the selection and choosing a valid combination of cycle and options will generally resolve the error without any parts replacement or technical repair work.

Source: manufacturer service documentation.

Common causes of F

  1. 01

    Incompatible cycle and option combination

    Wiring / connection

    The most frequent cause is selecting an add-on option, such as a specific spin speed or soil level, that is not supported by the chosen wash cycle. Review the option compatibility chart in your Use and Care Manual to find a valid pairing.

  2. 02

    Accidental button press during cycle selection

    Wiring / connection

    An unintended button press can add an option the user did not mean to select, creating a conflict with the active cycle. Canceling the cycle and starting the selection process fresh will typically resolve this.

  3. 03

    Control panel button sticking or registering false input

    Wiring / connection

    A sticky or partially stuck option button can cause the control board to register a selection that conflicts with the chosen cycle. Inspect the panel buttons for debris or physical damage that may cause unintended inputs.

  4. 04

    Control board retaining a previous conflicting setting

    Wiring / connection

    In some cases the control board may retain a previously selected option from an earlier cycle, creating a conflict when a new incompatible cycle is chosen. Performing a reset by unplugging the washer for one to two minutes can clear retained settings.

  5. 05

    Faulty user interface or control board

    Part replacement

    If the error persists after correcting all option selections, the user interface board or main control board may be misreading inputs or storing incorrect data. This is the least likely cause and would require component-level diagnosis and possible board replacement.

See the test procedure for each cause

Frequently asked questions about F

What does F mean on a Amana washer?
The F error code on an Amana washer means that an invalid option has been selected for the wash cycle currently chosen. The washer's control system detected a conflict between your cycle selection and one or more additional options. This is not a mechanical failure. It is a user input conflict that can be resolved by selecting a compatible combination of cycle and options.
How do I fix the F error code on my Amana washer?
Start by pressing the Cancel or Power button to clear the current selection. Then refer to the option compatibility information in your Use and Care Manual to choose a cycle and option combination that is listed as valid. Restart the washer with the corrected settings. If the error returns despite valid selections, try unplugging the washer for one to two minutes to reset the control board.
Is it safe to use my Amana washer when the F code is showing?
Yes, the F error code does not indicate a safety hazard. The washer is simply refusing to run because of an incompatible option selection, not because of a dangerous electrical or mechanical condition. The machine will not start the cycle until the conflict is resolved, which is a normal protective behavior.
Will resetting my Amana washer clear the F error code?
A reset can help if the control board is retaining a conflicting setting from a previous session. Unplug the washer from the power outlet, wait one to two minutes, then plug it back in. However, if you select the same invalid combination again, the F code will return. The underlying fix is selecting a valid cycle and option pairing.
How much does it cost to repair an Amana washer showing the F error code?
In most cases there is no repair cost because the F error is caused by an incompatible option selection rather than a broken part. If the error is traced to a faulty user interface board or main control board, replacement parts and labor could range from roughly $150 to $400 or more depending on the specific board and local labor rates. A technician diagnostic visit alone typically costs between $75 and $150.

Related Amana washer codes

All Amana washer codes
View all 33 Amana washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass