mypros+
Error code reference

Amana Washer Error Code rF

Pressure switch spin error

Amana codesAmana washer codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the rF error code actually means

Your Amana washer is showing an rF error because it detected a problem with water draining out or spinning, and the sensor that monitors water level is involved. This often means there is water left in the tub that needs to drain before the washer can spin properly. Try making sure your water faucets are on, unplug the washer for 10 seconds to reset it, and then run a spin or drain cycle to clear the water.

Diagnostic procedure

The full rF procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check to make sure water supply faucets are on, then connect electric power and spin out any water in the washtub (it may be necessary to unplug the washer for 10 seconds to clear the error).
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock rF procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of rF

Ranked by how often they cause this code
  1. 1Slow or incomplete draining
  2. 2Kinked or blocked drain hose
  3. 3Faulty or disconnected pressure switch air hose
  4. 4Defective pressure switch
  5. 5Drain pump failure

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about rF

What does rF mean on a Amana washer?
The rF code on an Amana washer indicates a pressure switch spin error. It means the washer detected a problem related to water drainage or spin conditions as monitored by the pressure switch. The code appears when the pressure switch signal does not match the expected state during the spin phase of the cycle, which is most often caused by water that has not fully drained from the tub.
Will resetting the washer clear the rF error code?
Unplugging the washer for 10 seconds is the recommended reset procedure and can clear the rF code if the underlying drainage issue was temporary. However, if the cause is a physical problem such as a blocked drain hose, a failing pump, or a damaged pressure switch air hose, the code will return after the reset once the washer attempts to spin again.
How much does it cost to repair an Amana washer showing the rF error?
Repair costs vary widely depending on the cause. If the fix is simply clearing a clogged drain hose or filter, costs may be minimal. Replacing a pressure switch air hose or a faulty pressure switch typically runs in the range of $75 to $200 including parts and labor. A full drain pump replacement can range from $150 to $350 depending on parts availability and local labor rates.
Can I fix the rF error myself without calling a technician?
In many cases, yes. Start by confirming the water supply faucets are fully open, then unplug the washer for 10 seconds to clear the error code. After restoring power, run a spin or drain-only cycle to remove any remaining water. If the error returns, inspect the drain hose for kinks or blockages and check the pump filter for debris before calling for service.
Is it safe to continue using my Amana washer when the rF code is displayed?
It is not recommended to continue running the washer while this error is active. The rF code indicates the spin cycle was interrupted because drainage conditions were not met, meaning there may be standing water in the tub. Running the washer in this state can strain the pump and motor, and leaving water sitting in the drum for extended periods can promote mold and odor buildup.

Related Amana washer error codes

All Amana washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass