mypros+
Error code reference

Bosch Oven Error Code E222

Cavity 2 meat probe sensor temperature too high

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E222 error code actually means

Your Bosch oven detected that the meat probe in the lower oven cavity is reading a temperature that is too high, so it shut off the heat as a precaution. This usually happens when the probe is plugged in but not actually inserted into the food, causing it to sense the full oven air temperature instead. Remove the probe from the oven, clear the error, and make sure to plug the probe back in only after it is inserted into the food.

Diagnostic procedure

The full E222 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check with customer to determine if probe was in receptacle and not in food; check probe operation and resistance; check for loose connections and/or pinched wires.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E222 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E222

Ranked by how often they cause this code
  1. 1Probe in receptacle but not in food
  2. 2Faulty meat probe thermistor
  3. 3Damaged probe cable
  4. 4Loose or corroded probe receptacle connection
  5. 5Control board misreading probe signal

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E222

What does E222 mean on a Bosch oven?
E222 indicates that the meat probe sensor in Cavity 2 has reported a temperature reading above the allowable limit, causing the oven to stop heating as a protective measure. The most common reason is that the probe was plugged into the receptacle but not inserted into food, exposing its tip directly to hot oven air. The oven will not resume heating in that cavity until the probe fault is resolved.
Is it safe to use my Bosch oven when E222 is displayed?
The oven halts heating in Cavity 2 when E222 is active, so active cooking in that cavity is not possible until the fault is cleared. The code is a protective response rather than a sign of a dangerous condition, but you should not attempt to bypass the error or force the oven to heat while the fault is present. Address the probe issue first, then resume normal operation.
How much does it cost to fix a Bosch oven E222 error that requires parts?
If the issue is a failed meat probe, replacement probe costs typically range from around $30 to $80 depending on the specific model. If the probe receptacle requires replacement, parts and labor can bring the total to somewhere between $100 and $250. Control board replacement, which is rarely needed for this error, is the most expensive repair and can range from $200 to $500 or more with labor.
How do I fix the E222 error on my Bosch oven?
Start by removing the meat probe from the receptacle and powering the oven off and back on to clear the error. If you plan to use the probe, insert it fully into the food before plugging it into the receptacle. If the error returns even with the probe correctly placed in food, inspect the probe cable for damage and test the probe resistance to determine whether the probe itself needs to be replaced.
Will resetting the oven clear the E222 error?
Powering the oven off at the circuit breaker or control panel and back on may clear the error temporarily, but it will return if the underlying cause is not resolved. If the probe was simply left in the receptacle without being in food, removing it and resetting the oven should clear the code permanently. If a faulty probe or damaged cable is causing the false reading, the error will reappear until those components are repaired or replaced.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass