mypros+
Error code reference

Bosch Refrigerator Error Code Co

Display Full Down mode.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Co error code actually means

The Co code means your Bosch refrigerator is in a special demo or showroom mode, which keeps the lights and display on but turns off the actual cooling system. Your refrigerator will not get cold while this mode is active. This is not a mechanical breakdown, but it does need to be corrected so your food stays at a safe temperature.

Diagnostic procedure

The full Co procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Co procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Co

Ranked by how often they cause this code
  1. 1Demo mode activated at installation
  2. 2Accidental button combination press
  3. 3Power interruption or reset
  4. 4Control board retaining demo mode setting

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Co

What does Co mean on a Bosch refrigerator?
The Co code on a Bosch refrigerator indicates the unit is in Display Full Down mode, which is a demo or showroom setting. In this state, the compressor and cooling system are turned off, though the display and interior lights remain active. The refrigerator will not cool food while this mode is active. Exiting demo mode through the control panel will restore normal cooling operation.
Is the Co code on a Bosch refrigerator dangerous?
The Co code itself does not indicate a hazardous condition, but it does mean the refrigerator is not cooling. Food stored in the unit while Co is active will not be kept at a safe temperature, which can lead to spoilage. It is best to address the code promptly and avoid storing perishable food until cooling is confirmed to have resumed.
How much does it cost to fix the Co code on a Bosch refrigerator?
In most cases, resolving the Co code costs nothing because it involves deactivating demo mode through the control panel with no parts required. If the control board is preventing the unit from exiting demo mode correctly, board replacement could range from moderate to higher repair costs depending on parts and labor in your area. A service call for diagnosis alone can range from around $75 to $150 or more depending on your location and the technician.
How do I fix the Co code on my Bosch refrigerator?
The Co code is typically resolved by pressing a specific button combination on the control panel to deactivate Display Full Down mode. The exact sequence varies by model, so consulting your unit's user guide for the demo mode exit procedure is recommended. Once the mode is deactivated, the compressor should resume and the Co code should clear. If the code returns after performing the correct steps, the control board may need further inspection.
Will resetting my Bosch refrigerator clear the Co code?
A simple power reset, such as unplugging the unit and plugging it back in, may not clear the Co code if the control board retains the demo mode setting after power is restored. The correct method is to exit Display Full Down mode using the designated control panel button sequence. If a power reset does clear the code, monitor the unit to ensure it does not re-enter demo mode on its own.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass