mypros+
Error code reference

Bosch Refrigerator Error Code E1003

UIM memory error parameter file

Bosch codesBosch refrigerator codes

UIM memory error parameter file

MyPros+ Max

Get the full diagnostic procedure for E1003.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E1003 means on a Bosch refrigerator

The E1003 error code on a Bosch refrigerator indicates a UIM (User Interface Module) memory error related to the parameter file. The UIM is the control board assembly responsible for managing the display panel, user inputs, and stored configuration data. When E1003 triggers, the module has detected a fault in reading, writing, or validating its internal parameter file, which contains critical operating settings such as temperature thresholds, display calibration data, and appliance configuration values.

This type of memory fault typically points to corruption or loss of data within the UIM's non-volatile memory (EEPROM or flash storage). The parameter file holds essential values that the module references during normal operation. If this file becomes corrupted due to a power surge, an interrupted write cycle, or memory degradation over time, the UIM cannot verify the integrity of its configuration and will trigger E1003 to flag the condition.

In most cases, the UIM itself is the failed component, as memory faults of this nature are internal to the module and cannot be repaired at the component level by field technicians. A power reset may temporarily clear the error if the fault was caused by a transient voltage event, but recurring E1003 codes strongly indicate that the UIM requires replacement. Electrical supply issues, such as unstable line voltage or inadequate surge protection, can accelerate memory degradation and should be evaluated as part of the diagnostic process.

Source: manufacturer service documentation.

Common causes of E1003

  1. 01

    UIM EEPROM or flash memory corruption

    Part replacement

    The parameter file stored in the User Interface Module's internal memory has become corrupted or unreadable. This is the most direct cause of E1003 and typically requires UIM board replacement.

  2. 02

    Power surge or voltage fluctuation

    Wiring / connection

    A sudden spike or drop in line voltage can interrupt a memory write cycle, corrupting the parameter file. Check whether the error appeared after a power outage or storm event.

  3. 03

    Failed or degraded UIM control board

    Part replacement

    Over time, the UIM board's memory components can degrade, leading to persistent parameter file errors. If the error returns after a reset, the board itself is likely the source.

  4. 04

    Loose or corroded wiring connections to the UIM

    Wiring / connection

    Poor electrical connections to the User Interface Module can cause intermittent communication and power delivery issues that destabilize memory operations. Inspect all harness connectors at the UIM for corrosion or looseness.

See the test procedure for each cause

Frequently asked questions about E1003

What does E1003 mean on a Bosch refrigerator?
E1003 on a Bosch refrigerator indicates a memory error in the User Interface Module (UIM) related to its internal parameter file. This parameter file stores critical configuration and operating settings for the appliance. When the UIM cannot read or validate this file, it triggers the E1003 fault code. The error can result from memory corruption, a power surge, or a failing UIM board.
Can I fix E1003 myself or do I need a technician?
You can attempt a power reset by unplugging the refrigerator for several minutes and then restoring power, which may clear the error if it was caused by a temporary voltage issue. If the code returns after the reset, the repair will likely involve replacing the User Interface Module, which requires identifying the correct replacement part and basic appliance disassembly skills. A qualified technician is recommended if you are not comfortable working with appliance control boards.
Will resetting the refrigerator clear the E1003 error?
A power reset by unplugging the unit for a few minutes can clear E1003 if the fault was triggered by a transient event such as a power fluctuation. However, if the UIM's memory is physically degraded or the parameter file is permanently corrupted, the error will return after the reset. Repeated recurrence of E1003 after resets is a strong indicator that the UIM board needs to be replaced.
Is it safe to keep using my Bosch refrigerator while E1003 is showing?
A UIM memory error can affect the accuracy of temperature displays and user controls, meaning you may not be able to fully verify or adjust operating settings. Food safety could be a concern if the refrigerator's temperature management is disrupted. It is advisable to monitor internal temperatures with a separate thermometer and address the fault promptly rather than continuing to rely on the appliance normally.
How much does it cost to repair a Bosch refrigerator E1003 error?
If the issue requires replacing the User Interface Module, parts costs typically range from around $100 to $300 or more depending on the specific Bosch model. Adding professional labor, the total repair cost can range from roughly $200 to $500 or higher. If the error is cleared by a simple power reset and does not return, there may be no parts cost at all.

Related Bosch refrigerator codes

All Bosch refrigerator codes
View all 209 Bosch refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass