mypros+
Error code reference

Dacor Refrigerator Error Code F

FoodSaver module fan rotation not detected during FoodSaver diagnostic test.

Dacor codesDacor refrigerator codes

FoodSaver module fan rotation not detected during FoodSaver diagnostic test.

First step from the service manual

Check fan motor connections and replace FoodSaver module if fan is not operating.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F means on a Dacor refrigerator

The F error code on a Dacor refrigerator indicates that the FoodSaver module's internal fan failed to produce detectable rotation during the FoodSaver diagnostic test cycle. The FoodSaver module is a specialized compartment designed to maintain specific humidity and temperature conditions for food preservation. During its self-diagnostic routine, the system monitors the fan motor for confirmed rotation. If the control board receives no feedback confirming the fan is spinning, it triggers the F code and halts normal FoodSaver operation.

The fan within the FoodSaver module is critical to circulating air evenly throughout the compartment. Without proper airflow, the module cannot maintain its intended preservation environment, and food stored inside may not be kept at the correct conditions. The most common causes include a disconnected or damaged wiring harness at the fan motor, a seized or burned-out fan motor, or a failure within the FoodSaver module's control circuitry that prevents the motor from receiving the correct operating signal.

Diagnosis begins by inspecting all electrical connections to the fan motor inside the FoodSaver module. Loose, corroded, or broken connectors are frequently responsible and should be reseated or replaced before condemning the module itself. If connections are intact and the fan still does not operate when powered, the FoodSaver module assembly should be replaced, as the fan motor and its associated components are typically integrated into the module unit.

Source: manufacturer service documentation.

Common causes of F

  1. 01

    Loose or disconnected fan motor wiring

    Wiring / connection

    The wiring harness connecting the FoodSaver fan motor may have come loose or been pulled free from its connector. Inspect all wire connections at the fan motor and reseat any loose plugs before further testing.

  2. 02

    Failed FoodSaver fan motor

    Part replacement

    The fan motor itself may be seized or burned out, preventing any rotation even when power is present. If connections are secure and the motor does not spin when the module is powered, the motor has likely failed.

  3. 03

    Damaged wiring harness

    Part replacement

    A wire in the harness running to the fan motor may be broken, chafed, or shorted, interrupting the electrical signal needed to drive the fan. Visually inspect the harness along its full length for damage.

  4. 04

    FoodSaver module control circuit failure

    Part replacement

    If the fan and its wiring test as functional but the fan still does not operate, the internal control circuitry of the FoodSaver module may have failed. In this case, replacing the full module assembly is the recommended repair.

See the test procedure for each cause

Frequently asked questions about F

What does F mean on a Dacor refrigerator?
The F error code on a Dacor refrigerator means the FoodSaver module's fan did not show detectable rotation during the FoodSaver diagnostic test. The control system monitors this fan to confirm it is spinning, and displays the code when no rotation is detected. This indicates a problem with the fan motor, its wiring connections, or the FoodSaver module itself.
How do I fix the F error code on my Dacor refrigerator?
Start by checking all wiring connections at the FoodSaver module fan motor and reseating any loose or disconnected plugs. If the connections are secure and the fan still does not operate, the FoodSaver module will need to be replaced. A qualified technician can confirm whether the fault is in the wiring, the motor, or the module assembly before ordering parts.
Will resetting my Dacor refrigerator clear the F error code?
A reset may temporarily clear the F code, but it will return if the underlying issue with the FoodSaver fan is not resolved. The code is triggered by the diagnostic test detecting no fan rotation, so until the fan operates correctly, the error will reappear. Resetting is not a substitute for diagnosing and repairing the fan motor or its connections.
Is the F error code on a Dacor refrigerator a safety concern?
The F code does not typically indicate an immediate safety hazard, but it does mean the FoodSaver compartment is not functioning as intended. Food stored in the FoodSaver module may not be maintained at proper preservation conditions, which could affect food quality. The rest of the refrigerator should continue to operate normally while the FoodSaver fault exists.
How much does it cost to repair the F error code on a Dacor refrigerator?
Repair costs vary depending on whether the issue is a simple wiring fix or requires a full FoodSaver module replacement. A wiring repair or connector replacement is generally inexpensive, while replacing the FoodSaver module assembly can range from a few hundred dollars to over five hundred dollars including parts and labor. Getting a diagnostic visit from a certified technician will help identify the exact cause before committing to parts costs.

Related Dacor refrigerator codes

All Dacor refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass