Error code reference
Frigidaire Range Error Code HLd
Hold/Keep warm
Hold/Keep warm — the oven is in keep warm mode, maintaining food at serving temperature.
MyPros+ Max
Get the full diagnostic procedure for HLd.
- ✓Step-by-step tests with expected resistance, voltage, and continuity values
- ✓Wiring diagram references and connector pinouts from the OEM service manual
- ✓Verified part numbers when replacement is required
Get the full procedure→
$29/month · Cancel anytime · Or $9.95 3-day pass
M+
M+ Max·Frigidaire Range
HLd on my Frigidaire FCRE3052AS
M+
Hold/Keep warm — the oven is in keep warm mode
From Service Manual 976165, p.17:
1.Access service mode to confirm the active fault code and read stored error history.
2.Measure control board supply voltage at the test points. Expected: 12 VDC and 5 VDC; a drop below 4.75 VDC on the logic rail points to a failed onboard regulator.
3.Inspect all connectors on the main control for corrosion, thermal stress, or backed-out pins. Reseat each connector with the power disconnected.
Part 5304504863
Electronic control board
Related Frigidaire range codes
All Frigidaire range codes →- - -Lockout indicator
- -SE-Shorted key
- 1RTD Sensor Error
- 1c1cShorted key detected
- 1c2cKeyboard tail disconnected
- 1c31Cancel key circuit problem
- 1c6cEEPROM error
- 1c7cControl not calibrated
View all 186 Frigidaire range codes
- 1c8cCooking program error
- 1d11Runaway temperature (650°F) with door unlocked
- 1d21Runaway temperature (950°F) with door locked
- 3d11Oven temperature sensor open
- 3d21Oven temperature sensor shorted
- 4d11Door switch not closed when door is locked.
- 4d51Door switch not open or closed
- 8Cooling Fan Error
- 9d11Latch will not lock
- CFCheck Food
- CLEAn dELAyDisplayed when attempting to start consecutive self-clean…
- CLnSelf-clean cycle is active
- CLODoor open during clean cycle
- d-0Steam clean door open indicator
- dODoor open alarm during broil
- doorControl thinks the lock switch is open when the oven is…
- door LocDoor lock indicator
- door OPnDoor open indicator
- ESurface control error indicator displayed (flashing E) at…
- E-08Oven heating error
- E-0AOven heating over
- E-0EDoor locking error
- E-27Oven sensor opened (resistance over 2950 ohms).
- E-28Oven sensor shorted (resistance under 930-940 ohms).
- E011Shorted keypad detected on ESEC surface element control.
- E013Bad EEPROM on the ESEC User Interface Board.
- E014Loss of Display tail #0 or #1, or Loss of Keyboard Tail…
- E015ESEC self test failed; ESEC-UIB may not be receiving a…
- E11Shorted keypad on ESEC surface element control.
- E13Bad EEPROM on ESEC UIB.
- E14TST/Display tail missing
- E15ESEC self test failed.
- E20Loss of LIN communication between ESEC UIB and EOC.
- E21Loss of communication between UIB and pan sensing PCB.
- E41Hall effect sensor error (cooling fan failure).
- E60Ambient oven temperature error for ESEC 20 UIB.
- E61Ambient oven temperature error for the pan sensing PCB.
- EndThe programmed cooking time or timer countdown has finished…
- ErError indicator displayed (flashing 'Er') at power up or…
- FElectronic surface control error displayed at startup or…
- F0 15ESEC Self-test failure.
- F001Touch failure on the oven user interface board.
- F002Touch failure on the oven user interface board.
- F003The oven user interface board is incorrectly configured.
- F004Touch failure on the oven user interface board.
- F005Touch failure on the oven user interface board.
- F01Touch Panel Failure
- F010Oven temperature runaway
- F011Stuck key
- F012Keyboard configuration alarm
- F013Data written to non-volatile memory has failed verification.
- F017The oven user interface board is unable to configure the…
- F018Oven relay board failure (wiggler).
- F019The oven user interface board is unable to configure the…
- F02Touch Panel Failure
- F020Communication failure between the oven user interface board…
- F022Communication failure between the oven user interface board…
- F023Communication failure between the oven user interface…
- F025The communication between the oven user interface and the…
- F027The communication between the oven user interface and the…
- F028The communication between the oven user interface…
- F029The communication between the oven user interface…
- F03The oven user interface board is incorrectly configured.
- F030Open oven temperature sensor (RTD).
- F031Shorted oven temperature probe (RTD).
- F033Meat probe temperature sensor shorted or too hot (triggered…
- F04Touch Panel Failure
- F05Touch Panel Failure
- F050A/D Out of Range
- F090MDL mechanism failure
- F095MDL mechanism failure
- F096The oven door has been detected open during a self-clean…
- F097MDL invalid state
- F098Magnetron case sensor probe shorted (NTC sensor on the…
- F099Magnetron case sensor probe open (NTC sensor on the…
- F1Potential runaway oven condition
- F10Example error code displayed when the electronic control…
- F100Magnetron case sensor temperature over-temp limit
- F101Magnetron auto power limit active based on temperature…
- F102Magnetron auto power limit active based on runtime limit…
- F104Loss of communication between GPU and OUI.
- F105Wake up procedure failure between OUI and GPU
- F106GPU configuration error
- F107Loss of communication between OUI and NIU
- F108NIU provisioning failed (Connection Fail)
- F109OTA (over-the-air) update failed
- F11Electronic control has detected a fault condition (example…
- F110NIU serialization failed (manufacturing only, not at user…
- F111Touch screen error from GPU
- F12Keyboard configuration alarm
- F13Data Written to Non-Volatile Memory has Failed Verification
- F14Misconnected keyboard cable between the keyboard membrane…
- F15Internal control or power supply failure between Power…
- F16The Oven User Interface Board Cannot Read the…
- F17The Oven User Interface Board is Unable to Configure the…
- F18Oven Relay Board Failure
- F19The Oven User Interface Board is Unable to Configure the…
- F2Control has detected a problem with the communications link…
- F20Control has detected a problem with the communications link…
- F22Communication Failure between the Oven User Interface Board…
- F23Control has detected a problem with the communication link…
- F24Communication failure between VSC board and EOC (lower oven…
- F25The Communication between the Oven User Interface and the…
- F26Communication failure with Mini Oven Control Board (for…
- F27The Communication between the Oven User Interface and the…
- F28The Communication between the Oven User Interface and the…
- F29The Communication between the Oven User Interface and the…
- F3Open RTD sensor probe/wiring problem (F30) or shorted RTD…
- F30Open RTD sensor probe or wiring problem (open condition in…
- F31Shorted RTD sensor probe or wiring problem
- F33Meat probe temperature sensor shorted or too hot (triggered…
- F40Cooktop lockout failure (some models).
- F42EOC internal software configuration error.
- F45Cooling fan speed low in upper cavity (Microcombi will…
- F46Cooling fan speed high in upper cavity (Microcombi will…
- F47Cooling fan speed low in lower cavity.
- F48Cooling fan speed high in lower cavity.
- F5ESEC has detected an internal circuit failure in the…
- F5 01ESEC Power Board not communicating.
- F5 02UIB not communicating.
- F5 A0Bad EEPROM checksum on ESEC Power Board.
- F5 F0Watchdog timer timed out on Power Board.
- F5 FFWatchdog timer timed out on UIB.
- F50A/D Out of Range
- F500Loss of LIN Buss communication between EOC and ESEC.
- F60Electronic Oven Control (EOC) over temperature
- F62Improper or corrupt signal voltage between the EOC and…
- F63Display communication error.
- F64Time base failure
- F65Keyboard short circuit or internal EOC failure.
- F66EOC internal power supply failure.
- F68High voltage condition
- F69High voltage condition
- F7ESEC has detected an internal circuit failure in the…
- F7 00Missing connection between Potentiometer/Display Board and…
- F7 01Missing connection between Potentiometer/Display Board and…
- F7 10Missing connection between Potentiometer/Display Board and…
- F7 11Potentiometer LF (Left Front) is shorted.
- F7 12Potentiometer for LF (Left Front) is wrong value.
- F7 20Potentiometer LR (Left Rear) is open.
- F7 21Potentiometer LR (Left Rear) is shorted.
- F7 22Potentiometer for LR (Left Rear) is wrong value.
- F7 30Potentiometer RR (Right Rear) is open.
- F7 31Potentiometer RR (Right Rear) is shorted.
- F7 32Potentiometer for RR (Right Rear) is wrong value.
- F7 40Potentiometer RF (Right Front) is open.
- F7 41Potentiometer RF (Right Front) is shorted.
- F7 42Potentiometer for RF (Right Front) is wrong value.
- F702Shorted Keypad on the ESEC.
- F9Latch motor problem
- F90Motor Door Lock Mechanism Failure
- F91Door motor mechanism failure (F90 to F94 range).
- F92Door motor mechanism failure (F90 to F94 range).
- F93Door motor mechanism failure (F90 to F94 range).
- F94Door motor mechanism failure (end of range F90–F94).
- F95Motor Door Lock mechanism failure
- F96The Oven Door has been Detected Open during a Self Clean…
- F97MDL invalid state
- HEHot Element indicator displayed on ESEC surface element…
- HotThe oven is still too hot to open the door safely…
- LEDs 3+7Problem with the communication link between the oven…
- LEDs 4+5Oven control not properly calibrated at the factory.
- LEDs 4+5+6Door motor mechanism failure.
- LEDs 4+6Control has sensed a potential runaway oven condition…
- LEDs 4+7Open RTD sensor probe / wiring problem.
- LEDs 5+7Incorrect Micro ID, controller self check failed.
- LEDs 6+7Incorrect EEPROM Checksum, control internal checksum may…
- LinE ERREOC internal voltage test error or failure.
- LocOven lockout feature is active; displayed when any control…
- LOC ONLock Controls feature is activated, preventing cooker…
- LOCK DOORThe self-clean cycle has been selected but the oven door is…
- PErrThe probe connector was not fully inserted into the jack…
- PFPower failure has occurred; the timer in the display will…
- Prob ERRThe oven probe is not detected or is defective
- Prob Too HotThe probe sensor temperature has exceeded 121°C (250°F); if…
- SAbSabbath mode is active
- SCCSelf-clean cycle interrupted because the cooktop was used…
- SFSabbath Failure
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started →$29/month · Cancel anytime · Or $9.95 3-day pass