mypros+
Error code reference

Haier Dishwasher Error Code Pots & Pans + Light Wash + Rinse & Hold

Water not draining (three indicator lights flashing simultaneously).

Haier codesHaier dishwasher codes

Water not draining (three indicator lights flashing simultaneously).

First step from the service manual

Check whether the pipe work/drain hose is in good condition.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for Pots & Pans + Light Wash + Rinse & Hold.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What Pots & Pans + Light Wash + Rinse & Hold means on a Haier dishwasher

When a Haier dishwasher flashes the Pots & Pans, Light Wash, and Rinse & Hold indicator lights simultaneously, it signals a drain failure. This means the control system has detected that water inside the tub has not been evacuated within the expected time window during or after a wash cycle. The dishwasher monitors drain pump operation and water level, and when drainage cannot be confirmed, it halts the cycle and triggers this three-light fault pattern to alert the user.

The drain system on a Haier dishwasher includes the drain pump, the drain hose routing from the pump to the household drain or garbage disposal, and the air gap or high-loop connection at the sink. A blockage, kink, or collapse anywhere along this path can prevent water from exiting the tub. The first diagnostic priority is a physical inspection of the drain hose for kinks, crushing, or disconnection, as these are the most common and easiest-to-resolve causes of drain faults.

Beyond the plumbing, a clogged filter or debris-blocked pump impeller can restrict flow enough to trigger the fault. If the drain path and filter are clear but water still will not evacuate, the drain pump motor itself may have failed electrically or mechanically. A failed pump will require component replacement to restore normal operation.

Source: manufacturer service documentation.

Common causes of Pots & Pans + Light Wash + Rinse & Hold

  1. 01

    Kinked or blocked drain hose

    Wiring / connection

    The drain hose running from the dishwasher to the sink drain or garbage disposal may be kinked, crushed, or clogged with debris. Inspect the full length of the hose for bends or obstructions and straighten or clear as needed.

  2. 02

    Clogged filter or sump

    Wiring / connection

    Food particles and debris can accumulate in the dishwasher filter and sump area, restricting water flow to the drain pump. Remove, inspect, and clean the filter assembly at the bottom of the tub.

  3. 03

    Blocked garbage disposal or drain connection

    Wiring / connection

    If the drain hose connects to a garbage disposal, a clogged disposal or an intact knock-out plug on a newly installed disposal can prevent drainage entirely. Run the disposal and verify the inlet port is clear.

  4. 04

    Blocked or faulty drain pump impeller

    Part replacement

    A foreign object such as a broken glass fragment or seed pit can jam the drain pump impeller. Access the pump and check for obstructions; if the impeller is damaged rather than just blocked, the pump will need replacement.

  5. 05

    Failed drain pump motor

    Part replacement

    If all plumbing and filter checks pass but water still will not drain, the drain pump motor may have failed electrically. This requires replacement of the drain pump assembly.

See the test procedure for each cause

Frequently asked questions about Pots & Pans + Light Wash + Rinse & Hold

What does Pots & Pans + Light Wash + Rinse & Hold mean on a Haier dishwasher?
These three indicator lights flashing at the same time is Haier's way of signaling a drain failure. The dishwasher detected that water in the tub did not drain within the expected time during the cycle. The machine stops and waits until the drainage issue is resolved before it will resume or start a new cycle.
How do I fix the drain error on my Haier dishwasher?
Start by checking the drain hose for kinks, blockages, or loose connections along its full length. Next, remove and clean the filter at the bottom of the dishwasher tub. If the dishwasher drains into a garbage disposal, run the disposal to clear it and confirm the connection port is open. If those steps do not resolve the issue, the drain pump impeller or motor may need to be inspected or replaced.
Is it safe to use my Haier dishwasher when this drain error is showing?
You should not run the dishwasher while this fault is active. Standing water in the tub can develop bacteria and odors, and continuing to run cycles without proper drainage can put strain on the pump motor. Resolve the drainage problem before resuming normal use.
Will resetting my Haier dishwasher clear the drain error?
A reset may clear the indicator lights temporarily, but if the underlying drainage problem is not fixed, the fault will return as soon as the dishwasher attempts to drain again. Address the physical cause first, such as a blocked hose, clogged filter, or faulty pump, before relying on a reset.
How much does it cost to repair a Haier dishwasher drain error?
If the fix is simply clearing a kinked hose or cleaning the filter, there is no parts cost involved. If the drain pump needs replacement, parts alone typically range from around $25 to $80 depending on the model, with additional labor costs if a technician performs the repair. A plumbing-related fix at the sink connection or garbage disposal may carry its own service cost if a plumber is needed.

Related Haier dishwasher codes

All Haier dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass