mypros+
Error code reference

Ikea Dishwasher Error Code PF

A power failure has occurred.

Ikea codesIkea dishwasher codes

A power failure has occurred.

MyPros+ Max

Get the full diagnostic procedure for PF.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What PF means on a Ikea dishwasher

The PF error code on an Ikea dishwasher stands for Power Failure. This code is triggered when the appliance detects that electrical power was interrupted during an active wash cycle. The dishwasher's control board monitors power supply continuity throughout operation, and when that continuity is broken unexpectedly, the board logs the PF code upon power restoration to alert the user that the cycle did not complete normally.

Power failures can originate from several sources: a tripped circuit breaker, a blown fuse in the home's electrical panel, a loose or faulty wall outlet connection, or an actual utility outage from the power company. The dishwasher itself is not necessarily malfunctioning when this code appears. The control board is simply reporting a historical event rather than an active component fault.

Because the wash cycle was interrupted, the dishwasher may have dishes that were left in a partially washed or unrinsed state. Detergent may also have been dispensed but not fully rinsed away. After clearing the code, it is advisable to inspect the power source for stability and run a fresh cycle to ensure dishes are properly cleaned. If PF codes appear repeatedly without an obvious external power interruption, the home's wiring or the dishwasher's power connection should be inspected for intermittent faults.

Source: manufacturer service documentation.

Common causes of PF

  1. 01

    Utility power outage

    Wiring / connection

    A neighborhood or building-wide power outage is the most frequent cause of a PF code. If other appliances or lights also lost power around the same time, this is likely the cause.

  2. 02

    Tripped circuit breaker

    Wiring / connection

    The circuit breaker dedicated to the dishwasher may have tripped, cutting power mid-cycle. Check the home's electrical panel for any breakers in the off or middle position and reset if found.

  3. 03

    Loose power cord or wall outlet connection

    Wiring / connection

    A poorly seated plug or a faulty wall outlet can cause intermittent power loss. Inspect the outlet for looseness and confirm the dishwasher's power cord is fully and securely connected.

  4. 04

    Faulty wall outlet or wiring

    Wiring / connection

    If the outlet itself is worn or the home wiring has an intermittent fault, power interruptions can occur without a breaker tripping. Testing the outlet with a multimeter or a known working device can help identify this issue.

  5. 05

    Failing control board

    Part replacement

    In rare cases where PF codes recur repeatedly with no external power interruption detected, the control board may be misreading power supply conditions due to an internal fault. Board replacement would be required if confirmed.

See the test procedure for each cause

Frequently asked questions about PF

What does PF mean on a Ikea dishwasher?
PF stands for Power Failure on an Ikea dishwasher. It indicates that the appliance lost electrical power during an active wash cycle. The control board stores this code and displays it when power is restored so the user knows the cycle did not complete. It is a notification code, not necessarily a sign that the dishwasher itself has a defect.
Will resetting the dishwasher clear the PF code?
Yes, in most cases the PF code can be cleared by pressing the Cancel or Reset button, or by cycling power to the unit. Because PF is a record of a past event rather than an ongoing fault, clearing it is straightforward. However, if the underlying power issue is not resolved, the code will return the next time a cycle is interrupted.
How do I fix the PF error on my Ikea dishwasher?
Start by checking your home's circuit breaker panel for any tripped breakers and reset them if needed. Confirm that the dishwasher's power cord is firmly plugged in and that the outlet is functioning properly. Once the power source is stable, clear the code and run a new cycle. If the code keeps returning without any obvious power interruption, have a qualified electrician inspect the outlet and wiring.
Is it safe to use my Ikea dishwasher after a PF error?
Yes, it is generally safe to use the dishwasher after a PF error once the power supply is confirmed to be stable. The code does not indicate any internal component damage or water-related hazard. Simply clear the code, check your power source, and run a fresh cycle. If you notice repeated PF codes or any unusual behavior, stop use and investigate the electrical supply further before continuing.
How much does it cost to repair a PF error on an Ikea dishwasher?
In most cases, resolving a PF error costs nothing because the cause is simply an external power interruption that self-resolves. If a faulty wall outlet needs replacement, repair costs typically range from $75 to $200 depending on the electrician and parts involved. In the uncommon scenario where the dishwasher's control board is at fault, board replacement can range from $150 to $400 or more including parts and labor.

Related Ikea dishwasher codes

All Ikea dishwasher codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass