mypros+
Error code reference

KitchenAid Microwave Error Code F6E2

Clean oven over temperature.

KitchenAid codesKitchenAid microwave codes

Clean oven over temperature.

First step from the service manual

Turn oven on and visually inspect all elements to ensure none are operating when they should not be; enter diagnostics and test relay cycling.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for F6E2.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F6E2 means on a KitchenAid microwave

The F6E2 error code on a KitchenAid microwave indicates a clean oven over-temperature condition. This fault is triggered when the oven's thermal monitoring system detects that the cavity temperature has exceeded the safe threshold during or after a self-clean cycle. The control board monitors temperature through a dedicated thermal sensor or thermostat, and when readings climb beyond the acceptable limit, the board logs this fault to protect internal components and prevent a potential safety hazard.

The most common root cause involves a relay on the control board that has failed in the closed position, causing a heating element to remain energized when it should be off. This is why the first diagnostic step involves powering on the oven and visually confirming that no elements are glowing or active during a period when they should be inactive. Entering the service diagnostics mode and testing relay cycling allows a technician to verify whether each relay is properly opening and closing on command.

Additional causes can include a faulty temperature sensor reporting inaccurate high readings, a defective thermostat that fails to interrupt power at the correct temperature, or a control board that is sending incorrect signals to the heating circuit. In some cases, a genuine over-temperature event caused by a blocked vent or restricted airflow can trigger this code without any component failure. Identifying whether the temperature rise is real or sensor-reported is a critical early step in the diagnostic process.

Source: manufacturer service documentation.

Common causes of F6E2

  1. 01

    Relay Stuck Closed on Control Board

    Part replacement

    A relay on the control board can fail in the closed position, keeping a heating element energized when the cycle calls for it to be off. Visual inspection during power-on and relay cycle testing in diagnostics mode will confirm this condition.

  2. 02

    Faulty Temperature Sensor

    Part replacement

    A defective thermal sensor may report temperatures that are higher than the actual cavity temperature, causing the control board to trigger the over-temperature fault incorrectly. Resistance testing of the sensor can confirm whether its readings fall within the expected range.

  3. 03

    Defective Thermal Thermostat

    Part replacement

    The oven thermostat is designed to cut power to the heating circuit when a safe temperature limit is reached. If it fails to open at the correct threshold, temperatures can continue to rise and trigger the F6E2 code.

  4. 04

    Blocked Ventilation or Restricted Airflow

    Wiring / connection

    If the oven cavity vents are obstructed by grease buildup or external blockage, heat cannot dissipate properly and a genuine over-temperature condition can occur. Inspect vents and clean the cavity thoroughly before further component testing.

  5. 05

    Control Board Sending Incorrect Signals

    Part replacement

    A malfunctioning control board may send incorrect commands to the heating circuit, activating elements outside of programmed cycles. This is typically identified after ruling out individual component failures through diagnostics.

See the test procedure for each cause

Frequently asked questions about F6E2

What does F6E2 mean on a KitchenAid microwave?
F6E2 indicates a clean oven over-temperature fault. The control board has detected that the oven cavity temperature exceeded a safe limit during or after the self-clean cycle. This is often caused by a relay stuck closed that keeps a heating element on when it should be off, though a faulty temperature sensor can also trigger the code. The appliance halts operation to prevent damage or a safety hazard.
Can I fix the F6E2 error myself?
Some basic steps can be performed safely at home, such as inspecting the oven cavity for ventilation blockages and cleaning out any grease buildup. However, diagnosing a stuck relay or a failed temperature sensor requires entering the service diagnostics mode and performing electrical tests, which is best handled by a qualified technician. Replacing a control board or thermal component also involves working with high-voltage circuits.
Is it safe to use my KitchenAid microwave while the F6E2 code is displayed?
You should not continue using the appliance until the fault has been diagnosed and resolved. The code indicates that the oven reached an unsafe temperature, which may mean a heating element is not turning off as expected. Continued operation under this condition could cause further damage to components or pose a fire risk.
Will resetting my KitchenAid microwave clear the F6E2 error?
A power reset may temporarily clear the fault code from the display, but it will not fix the underlying cause. If a relay is stuck, a sensor is faulty, or the control board is sending incorrect signals, the error will return once the appliance runs again. A reset can be useful as an initial step to confirm the code, but full diagnostic testing is still required.
How much does it cost to repair a KitchenAid microwave with an F6E2 error?
Repair costs depend on which component has failed. A temperature sensor is typically a lower-cost part, while a control board replacement can range significantly higher, often between $150 and $400 or more including labor. If a relay on the control board is the cause, the board usually needs to be replaced as a unit. Getting a diagnostic service call from a technician will give you a more precise estimate based on your specific model.

Related KitchenAid microwave codes

All KitchenAid microwave codes
View all 60 KitchenAid microwave codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass