mypros+
Error code reference

LG Dryer Error Code LE2

Low electric current detected

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the LE2 error code actually means

The LE2 code means your LG dryer detected that its compressor is not drawing enough electrical power to run properly, so the dryer shut itself off to prevent damage. This type of dryer uses a compressor similar to what you find in an air conditioner, and it is sensitive to blocked filters and room temperature. Start by cleaning the lint filters completely and making sure the room where the dryer sits is not too cold or too hot.

Diagnostic procedure

The full LE2 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check the lint double filter and remove lint. Check ambient temperature around appliance.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock LE2 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of LE2

Ranked by how often they cause this code
  1. 1Clogged lint double filter
  2. 2Ambient temperature out of range
  3. 3Failing or seized compressor
  4. 4Wiring fault in the compressor circuit
  5. 5Faulty main control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about LE2

What does LE2 mean on a LG dryer?
LE2 indicates that the dryer detected low electrical current at the compressor. The dryer attempts to restart the compressor three times and, if the condition persists, shuts down and displays the code. LG heat pump dryers are particularly sensitive to airflow restrictions and ambient temperature, both of which can cause this fault. Cleaning the lint double filter and checking room temperature are the first recommended diagnostic steps.
Is it safe to keep using my LG dryer while it shows the LE2 code?
No, you should not continue running the dryer while LE2 is active. The dryer has already shut itself down as a protective measure after detecting a compressor fault. Attempting to force continued operation could cause further damage to the compressor or related components. Address the cause of the error before resuming use.
How much does it cost to repair an LG dryer with an LE2 error?
Repair cost depends on the cause. If cleaning the lint filter and adjusting room temperature resolve the issue, there is no parts cost involved. If the compressor requires replacement, parts and labor costs can range from several hundred dollars to close to the cost of a new unit, depending on your region and the specific model. A wiring repair or control board replacement typically falls somewhere between those two extremes.
Can I fix the LE2 error myself without calling a technician?
In many cases, yes. Start by removing and thoroughly cleaning the lint double filter, as buildup is the most common cause of LE2. Also confirm that the room where the dryer is installed is within a normal temperature range and that ventilation around the appliance is not obstructed. If the error returns after these steps, the issue is likely a failing compressor or wiring problem that will require a qualified technician.
Will resetting my LG dryer clear the LE2 error code?
A reset may temporarily clear the display, but the code will return if the underlying cause is not resolved. The dryer goes through three compressor restart attempts before displaying LE2, so simply power cycling the unit without fixing the root issue will result in the same fault sequence. Clean the lint filter and check ambient conditions before resetting, so the compressor has a chance to operate normally.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass