mypros+
Error code reference

LG Heat Pump Error Code CH63

Temperature at condenser-pipe is too low.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the CH63 error code actually means

Your LG heat pump has detected that the temperature inside a key coil in the system is too low, which suggests something is preventing it from working efficiently. This could be caused by a refrigerant leak, a dirty or blocked coil, or a faulty sensor. The system has stopped normal operation to prevent damage, and a technician should inspect it before you try to continue using it.

Diagnostic procedure

The full CH63 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock CH63 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of CH63

Ranked by how often they cause this code
  1. 1Low refrigerant charge
  2. 2Faulty or mispositioned condenser pipe thermistor
  3. 3Restricted refrigerant flow
  4. 4Dirty or blocked condenser coil
  5. 5Condenser fan motor failure

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about CH63

What does CH63 mean on a LG heat_pump?
CH63 indicates that the temperature at the condenser pipe has been detected as too low by the system control board. This points to an issue with refrigerant charge, refrigerant flow, airflow across the condenser coil, or the condenser pipe temperature sensor itself. The system triggers this code as a protective measure to prevent further damage. A qualified technician should diagnose the root cause before the unit is returned to service.
Is it safe to keep running my LG heat pump with a CH63 error?
It is not recommended to continue operating the unit while CH63 is active. The system has flagged a condition that compromises normal heat exchange, and running the equipment in this state can cause additional stress on the compressor and other components. Turn the unit off and schedule a diagnostic inspection to avoid more costly damage.
Will resetting my LG heat pump clear the CH63 error code?
A power reset may temporarily clear the CH63 code, but if the underlying cause has not been resolved, the fault will return during operation. Resetting the unit without addressing the root problem can mask a serious issue and allow damage to progress. It is best to use a reset only as part of a diagnostic process after a repair has been made, not as a standalone fix.
Can I fix CH63 on my LG heat pump myself?
Some causes, such as cleaning a dirty condenser coil or removing a physical airflow obstruction, can be addressed without professional help. However, refrigerant-related causes require EPA-certified technicians and specialized equipment to diagnose and repair safely. Sensor replacement is also a task most DIYers can handle if they are comfortable with basic electrical testing, but confirming the correct resistance values for the thermistor is important before replacing any part.
How much does it cost to repair a CH63 error on an LG heat pump?
Repair costs vary widely depending on the root cause. A simple coil cleaning or sensor replacement may cost between $75 and $200 in labor. If a refrigerant leak is involved, costs typically range from $200 to $600 or more depending on the leak location and the amount of refrigerant needed. A failed fan motor replacement generally falls in the $150 to $400 range including parts and labor.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass