mypros+
Error code reference

LG Heat Pump Error Code E233

Fixed capacity compressor 2 discharge sensor error OPEN/SHORT

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E233 error code actually means

Your LG heat pump has detected a problem with the temperature sensor on one of its compressors. The sensor is reading a signal that is either too high or too low, which tells the system something is wrong with the sensor, its wiring, or its connector. The unit has stopped normal operation to protect the compressor from potential damage.

Diagnostic procedure

The full E233 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check sensor connector; measure resistance and compare to table.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E233 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E233

Ranked by how often they cause this code
  1. 1Failed discharge temperature sensor
  2. 2Corroded or loose sensor connector
  3. 3Damaged wiring harness
  4. 4Moisture ingress into sensor or connector
  5. 5Faulty outdoor control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E233

What does E233 mean on a LG heat_pump?
E233 indicates a discharge temperature sensor error on fixed capacity compressor 2. The system has detected that the sensor signal voltage is either above 4.95V (open circuit, corresponding to below -30°C) or below 0.5V (short circuit, corresponding to above 151°C). This fault is only detected when outdoor temperature is above -10°C. The cause is typically a failed sensor, a damaged connector, or a wiring problem between the sensor and the outdoor control board.
Is it safe to run my heat pump while E233 is active?
It is not advisable to continue operating the unit with E233 active. The discharge sensor protects compressor 2 from overheating, and without reliable temperature data the system cannot adequately safeguard the compressor. Continued operation risks compressor damage, which is a significantly more costly repair than fixing the sensor or wiring.
How much does it cost to repair an E233 error on an LG heat pump?
Repair costs depend on the root cause. A replacement discharge temperature sensor typically runs in the range of $20 to $80 for the part, plus labor. A wiring repair is generally in the $75 to $200 range depending on complexity. If the outdoor control board needs replacement, costs can range from $200 to $600 or more for parts and labor. Getting a diagnostic visit from a qualified technician is the best first step to determine the exact cause before committing to a repair.
Can I fix E233 myself, or do I need a technician?
Basic checks such as inspecting and reseating the sensor connector are within reach for a knowledgeable DIYer. However, accessing the discharge sensor inside an outdoor heat pump unit, measuring resistance against a specification table, and replacing components requires comfort with electrical testing and refrigeration systems. If the sensor or control board needs replacement, a qualified HVAC technician is recommended.
Will resetting my LG heat pump clear the E233 error?
A power reset may temporarily clear the error, but it will return if the underlying fault is still present. If the sensor connector was loose, reseating it before resetting may resolve the issue permanently. Any reset should be followed by monitoring the system to confirm the code does not reappear.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass