mypros+
Error code reference

LG Heat Pump Error Code E282

SUMP TEMP FIXED 1 sensor error (OPEN/SHORT)

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E282 error code actually means

Your LG heat pump has detected a problem with a temperature sensor located in the outdoor unit that monitors the sump area. The sensor is either broken, disconnected, or has a wiring fault, so the system cannot get a reliable temperature reading. Until this is fixed, the heat pump will not operate normally in order to protect the compressor from potential damage.

Diagnostic procedure

The full E282 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check sensor connector; measure resistance and compare to table.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E282 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E282

Ranked by how often they cause this code
  1. 1Loose or corroded sensor connector
  2. 2Failed or damaged temperature sensor
  3. 3Damaged sensor wiring
  4. 4Water or moisture intrusion at the connector
  5. 5Faulty outdoor unit control board

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E282

What does E282 mean on a LG heat_pump?
E282 indicates a fault with the SUMP TEMP FIXED 1 sensor in the outdoor unit, detected when outdoor temperatures are above -10°C. The error triggers when the sensor signal voltage goes above 4.95V, indicating an open circuit, or drops below 0.5V, indicating a short circuit. Both conditions mean the sensor is returning an implausible reading and the system has shut down to protect itself. The most common causes are a loose connector, a failed sensor, or damaged wiring.
Is it safe to run my LG heat pump while E282 is displayed?
No, you should not continue to operate the heat pump while E282 is active. The fault indicates that a critical sump temperature sensor is not providing reliable data, and running the unit without this protection could lead to compressor damage. It is best to leave the unit off until the sensor fault is diagnosed and corrected.
Will resetting my LG heat pump clear the E282 error?
A reset may temporarily clear the error code, but E282 will return if the underlying sensor fault is not repaired. Since the error is only triggered when outdoor temperatures are above -10°C, the fault condition that caused it is still present and will be detected again once the system runs. A proper fix requires inspecting the connector, measuring the sensor resistance, and replacing any faulty components.
Can I fix error E282 myself on my LG heat pump?
A homeowner can safely check whether the sensor connector is loose or visibly corroded and reseat it. However, measuring sensor resistance and comparing it to a specification table requires a multimeter and some technical knowledge. Replacing a sensor or wiring harness is generally within reach for a skilled DIYer, but if the control board is involved, a qualified technician should handle the repair.
How much does it cost to repair error E282 on an LG heat pump?
If only the sensor connector needs to be reseated, there may be no parts cost and only a service call fee, typically in the range of $75 to $150. Replacing the SUMP TEMP FIXED 1 sensor itself usually costs between $50 and $150 for the part, plus labor. If the control board needs replacement, total repair costs can range from $300 to $700 or more depending on the model and labor rates in your area.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass