mypros+
Error code reference

LG Heat Pump Error Code E283

SUMP TEMP FIXED 2 sensor error (OPEN/SHORT)

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E283 error code actually means

Your LG heat pump is detecting a problem with one of its temperature sensors in the outdoor unit. The sensor is either not sending any signal at all or is sending a signal that is out of the normal range, so the system has shut down to protect itself. A technician will need to check the sensor wiring and the sensor itself to determine whether it needs to be replaced.

Diagnostic procedure

The full E283 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check sensor connector; measure resistance and compare to table.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E283 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E283

Ranked by how often they cause this code
  1. 1Faulty or failed SUMP TEMP FIXED 2 sensor
  2. 2Loose or disconnected sensor connector
  3. 3Damaged or shorted wiring harness
  4. 4Corrosion at the connector terminals
  5. 5Control board input circuit fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E283

What does E283 mean on a LG heat_pump?
E283 indicates a fault with the SUMP TEMP FIXED 2 sensor in the outdoor unit. The sensor circuit is either open, with a signal voltage above 4.95V, or shorted, with a signal voltage below 0.5V. This error is only triggered when the outdoor temperature is above -10°C. The system flags this fault to protect the compressor and refrigerant circuit from operating with inaccurate sump temperature data.
Is it safe to run my LG heat pump while E283 is active?
It is not advisable to continue operating the heat pump while this error is active. The SUMP TEMP FIXED 2 sensor plays a role in protecting the compressor and refrigerant circuit, and running the system without accurate sump temperature data could result in compressor damage or refrigerant-related issues. Address the fault before resuming normal operation.
How much does it cost to repair an E283 error on an LG heat pump?
Repair costs vary depending on the root cause. If the fix involves reseating a connector or cleaning terminals, the cost may be limited to a service call fee, typically in the range of $75 to $150. Replacing the SUMP TEMP FIXED 2 sensor itself generally adds $50 to $200 in parts. If the control board is at fault, replacement costs can range from $300 to $700 or more including labor, depending on the specific model and your location.
Can I fix E283 myself, or do I need a technician?
A knowledgeable DIYer can perform the initial checks, such as inspecting the sensor connector and measuring sensor resistance with a multimeter. However, accessing the outdoor unit control board and interpreting the resistance-versus-temperature table requires some technical comfort with electrical diagnostics. If the sensor or wiring needs replacement, a qualified HVAC technician is recommended, especially since working inside the outdoor unit involves electrical components that can store charge.
Will resetting the heat pump clear the E283 error?
A power reset may temporarily clear the error display, but if the underlying fault with the sensor, connector, or wiring is still present, the code will return once the unit resumes operation and detects the out-of-range voltage signal again. A reset should only be performed after the root cause has been identified and corrected.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass