mypros+
Error code reference

LG Heat Pump Error Code E292

Low pressure sensor error OPEN/SHORT

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the E292 error code actually means

Your LG heat pump has detected a problem with the sensor that monitors refrigerant pressure on the low-pressure side of the system. The sensor is either sending no signal or a signal that is out of the normal range, so the system stopped the compressor from starting as a precaution. This is typically caused by a wiring issue or a faulty sensor, and a technician will need to inspect and test those components.

Diagnostic procedure

The full E292 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check low pressure sensor wiring and connector.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock E292 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of E292

Ranked by how often they cause this code
  1. 1Loose or disconnected sensor connector
  2. 2Damaged sensor wiring harness
  3. 3Failed low pressure sensor
  4. 4Corroded or damaged connector pins
  5. 5Control board input circuit fault

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about E292

What does E292 mean on a LG heat_pump?
E292 indicates a low pressure sensor error, either a SHORT or OPEN circuit condition in the sensor signal circuit. A SHORT is identified when the sensor voltage drops below 0.4V, and an OPEN is identified when it rises above 4.7V. The fault is detected when the compressor is preparing to operate, and it prevents the compressor from starting until the issue is resolved. The root cause is typically a wiring fault, failed connector, or a defective low pressure sensor.
Is it safe to run my LG heat pump with an E292 error?
The unit will not allow the compressor to start while E292 is active, which is a built-in protection measure. Operating the system in this state is not recommended, as the underlying fault means the control board cannot confirm safe refrigerant pressure conditions. Have the issue diagnosed and repaired before resuming normal operation.
Will resetting my LG heat pump clear the E292 error?
A power reset may temporarily clear the error code, but if the underlying fault in the low pressure sensor circuit is still present, the E292 code will return as soon as the compressor attempts to operate again. A reset is not a fix and should only be used as a diagnostic step to confirm whether the error is intermittent. The wiring, connector, and sensor must be inspected and tested to resolve the fault permanently.
Can I fix the E292 error myself?
Some basic checks, such as inspecting the sensor connector for loose connections or visible wire damage, can be performed by a knowledgeable DIYer. However, diagnosing sensor voltage output and working near refrigerant components requires proper tools and technical knowledge. If the issue involves the refrigerant circuit or control board, a certified HVAC technician should handle the repair.
How much does it cost to repair an E292 error on an LG heat pump?
Repair costs vary depending on what is causing the fault. A simple connector reseating or wiring repair might cost between $75 and $200 in labor. Replacing the low pressure sensor typically adds $50 to $150 in parts. If the control board input circuit is damaged, costs can rise significantly higher, potentially ranging from $300 to $700 or more depending on the board and labor rates in your area.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass