mypros+
Error code reference

LG Range Error Code C-d0

Shorted touch (touch keypad short circuit detected).

LG codesLG range codes

Shorted touch (touch keypad short circuit detected).

First step from the service manual

Disconnect power. Take out the assy Touch panel from the display PCB. Check whether between connector pin and pin on display PCB there is a short circuit.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for C-d0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What C-d0 means on a LG range

The C-d0 error code on an LG range indicates that the control system has detected a short circuit within the touch keypad assembly. The touch panel communicates with the display PCB through a connector interface, and when the resistance or signal state between connector pins falls outside expected parameters, the control interprets this as a shorted touch condition. This prevents normal operation to avoid unintended commands being sent to the cooking system.

The most common source of this fault is within the touch panel assembly itself, where internal membrane layers or conductive traces can contact each other due to physical damage, moisture intrusion, or manufacturing defects. Contamination from cooking grease or liquid spills can also bridge connector pins, creating an unintended electrical path that mimics a keypad press. In some cases, the ribbon cable or connector between the touch panel and the display PCB may be damaged or seated improperly.

Diagnosis begins by disconnecting power to the range, then physically removing the touch panel assembly from the display PCB. With the panel disconnected, you can check for continuity or low resistance between the individual connector pins on the display PCB side. If no short is found at the PCB connector with the panel removed, the fault is isolated to the touch panel assembly itself. If a short persists at the PCB connector even with the panel removed, the display PCB may require inspection or replacement.

Source: manufacturer service documentation.

Common causes of C-d0

  1. 01

    Failed touch panel assembly

    Part replacement

    Internal conductive layers within the touch membrane can short together due to age, physical damage, or repeated use. This is the most likely cause and is confirmed when the short clears after disconnecting the touch panel from the display PCB.

  2. 02

    Moisture or grease contamination

    Wiring / connection

    Liquid or grease entering the touch panel or its connector can bridge pins and create a false short signal. Inspect the panel and connector area for visible residue or corrosion.

  3. 03

    Damaged or improperly seated ribbon cable

    Wiring / connection

    The ribbon cable connecting the touch panel to the display PCB can be pinched, torn, or seated at an angle, causing pin-to-pin contact. Reseating or replacing the cable may resolve the fault.

  4. 04

    Shorted display PCB connector

    Part replacement

    If the short is detected at the display PCB connector pins even after the touch panel assembly is removed, the PCB itself may have damaged traces or a failed connector that requires board repair or replacement.

  5. 05

    Physical damage to the touch panel surface

    Part replacement

    Cracks or deep scratches on the glass or membrane overlay can cause internal layers to contact each other. Look for visible damage to the panel surface around the control area.

See the test procedure for each cause

Frequently asked questions about C-d0

What does C-d0 mean on a LG range?
C-d0 is a touch keypad short circuit error. It means the display PCB has detected an unintended electrical short between connector pins in the touch panel circuit. The range will suspend normal operation until the fault is diagnosed and corrected.
Will resetting the power clear the C-d0 error on my LG range?
A power reset may temporarily clear the display, but if the underlying short circuit is still present in the touch panel or its connector, the C-d0 code will return. A permanent fix requires identifying and correcting the source of the short, either by cleaning the connector, reseating the cable, or replacing the touch panel assembly.
Is it safe to use my LG range while the C-d0 error is active?
It is not recommended to operate the range while C-d0 is active. A shorted touch input could send unintended commands to the cooking elements or burners. Disconnect power and have the fault diagnosed before resuming use.
How do I fix the C-d0 error on my LG range?
Start by disconnecting power to the range and removing the touch panel assembly from the display PCB. Check for continuity between connector pins on the display PCB with the panel removed. If the short clears, the touch panel assembly is faulty and needs replacement. If the short remains, the display PCB requires further inspection. Clean any visible contamination from the connector before reassembling.
How much does it cost to repair a C-d0 error on a LG range?
Repair costs depend on which component is at fault. A replacement touch panel assembly typically ranges from $50 to $150 for parts, while a display PCB can range from $100 to $300 or more. Adding professional labor usually brings total repair costs to somewhere between $150 and $500 depending on the specific model and the extent of the damage.

Related LG range codes

All LG range codes
View all 39 LG range codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass