mypros+
Error code reference

LG Refrigerator Error Code 08

Freezer fan motor error

LG codesLG refrigerator codes

Freezer fan motor error - operation failure, feedback signal line contact failure, or motor wire missing.

First step from the service manual

Check voltage between MAIN PCB CN75 #4 (YELLOW) and #10 (GRAY); should be 7V~12V.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for 08.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What 08 means on a LG refrigerator

Error code 08 on an LG refrigerator indicates a freezer fan motor fault. The freezer evaporator fan is responsible for circulating cold air from the evaporator coil throughout the freezer and refrigerator compartments. When the main PCB detects a problem with this fan's operation or its feedback signal, it logs error 08 and may shut down cooling to prevent component damage. The fault can stem from three distinct failure modes: the motor itself failing to operate, a break or poor connection in the feedback signal line between the fan and the control board, or a missing or disconnected motor wire harness.

The primary diagnostic step is to measure the supply voltage at the main PCB connector CN75, specifically between pin 4 (YELLOW wire) and pin 10 (GRAY wire). This voltage should read between 7V and 12V during normal operation. A reading within this range confirms the board is sending power to the fan circuit, which shifts suspicion toward the fan motor itself, its wiring harness, or the feedback signal wire. A voltage reading outside this range points toward a main PCB failure or a wiring fault between the board and the connector.

Beyond voltage supply issues, the feedback signal line is a common culprit. The freezer fan motor sends a tachometer or Hall-effect feedback pulse back to the PCB so the board can confirm the motor is spinning at the correct speed. If this signal line is broken, corroded, or has a loose connector pin, the board will interpret the motor as non-functional even if the motor itself is receiving adequate power. Inspecting the full wire harness from the fan to CN75 for pinched wires, corrosion at connector pins, or disconnected plugs is a critical part of diagnosing this error.

Source: manufacturer service documentation.

Common causes of 08

  1. 01

    Faulty freezer fan motor

    Part replacement

    The fan motor itself may have failed internally due to worn bearings, a burned winding, or a seized rotor. If voltage at CN75 pins 4 and 10 is within the 7V to 12V range but the fan does not spin, the motor is likely defective and needs replacement.

  2. 02

    Disconnected or broken feedback signal wire

    Wiring / connection

    The fan motor sends a feedback signal back to the PCB to confirm it is spinning. A broken, corroded, or disconnected feedback signal wire will cause the board to log error 08 even if the motor has adequate power supply. Inspect the harness from the fan to connector CN75 for damaged or loose wires.

  3. 03

    Loose or corroded wiring harness connector

    Wiring / connection

    Poor contact at the CN75 connector or at the fan motor plug can interrupt both power delivery and the feedback signal. Unplug and reseat all connectors in the fan circuit, and inspect the pins for corrosion or pushed-back terminals.

  4. 04

    Missing motor wire

    Wiring / connection

    A wire in the fan motor harness may be completely absent due to a previous repair, rodent damage, or a manufacturing defect. Visually trace the full harness from the fan motor to the main PCB and confirm all wires are present and properly terminated.

  5. 05

    Main PCB failure

    Part replacement

    If the voltage measured between CN75 pin 4 (YELLOW) and pin 10 (GRAY) falls outside the 7V to 12V specification and the wiring harness checks out, the main PCB may not be supplying correct power to the fan circuit. Board replacement would be required in this scenario.

See the test procedure for each cause

Frequently asked questions about 08

What does 08 mean on a LG refrigerator?
Error code 08 on an LG refrigerator signals a freezer fan motor fault. The refrigerator's control board has detected either an operational failure of the freezer evaporator fan motor, a problem with the feedback signal line that confirms the motor is running, or a missing or disconnected motor wire. This error can result in inadequate cooling in both the freezer and fresh food compartments.
Can I fix error code 08 on my LG refrigerator myself?
Some causes of error 08 are DIY-friendly. You can inspect the fan motor wiring harness for disconnected plugs, pinched wires, or visible corrosion and reseat any loose connectors without special tools. However, testing voltage at the main PCB connector CN75 requires a multimeter and basic electrical safety knowledge. Replacing a failed fan motor or PCB is also a task many experienced DIYers can complete, but if you are not comfortable working with appliance electronics, a qualified technician is recommended.
Is it safe to use my LG refrigerator while error code 08 is showing?
Continuing to use the refrigerator with an active error 08 is not recommended. The freezer fan is critical for moving cold air through both the freezer and refrigerator sections. Without it functioning correctly, food in both compartments may reach unsafe temperatures. It is best to address the error promptly and move perishable food to a working refrigerator in the meantime.
How much does it cost to repair error code 08 on an LG refrigerator?
Repair costs vary depending on the root cause. If the fix involves reseating a loose connector, there may be no parts cost at all. A replacement freezer evaporator fan motor typically costs in the range of $30 to $80 for the part, plus labor if a technician is hired. A main PCB replacement is more expensive, generally ranging from $100 to $300 or more for the part alone. Total repair bills including labor can range from $75 to $400 depending on the diagnosis.
Will resetting my LG refrigerator clear error code 08?
A reset may temporarily clear the error code from the display, but it will not fix the underlying hardware problem. If the freezer fan motor, wiring, or feedback signal line has a genuine fault, error 08 will return once the refrigerator restarts and the board re-checks the fan circuit. A reset is useful for confirming whether the fault is intermittent, but the wiring and motor should still be inspected to identify and correct the root cause.

Related LG refrigerator codes

All LG refrigerator codes
View all 485 LG refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass