mypros+
Error code reference

Maytag Refrigerator Error Code E0

No errors, functioning ice maker.

Maytag codesMaytag refrigerator codes

No errors, functioning ice maker.

MyPros+ Max

Get the full diagnostic procedure for E0.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What E0 means on a Maytag refrigerator

The E0 code on a Maytag refrigerator ice maker is a status indicator, not a fault code. When the ice maker diagnostic cycle is initiated and E0 is displayed, it signals that the control board has completed its self-check and found no active errors in the ice maker system. All monitored components, including the ice maker module, harvest cycle, water inlet valve signaling, and temperature sensors relevant to ice production, are operating within expected parameters.

This code appears during or after a manual diagnostic test sequence on the ice maker. Technicians typically enter this mode by pressing a specific button sequence on the ice maker control to cycle through stored error codes. When E0 appears, it means the system's error memory is clear and the ice maker is functioning as designed. No corrective action is required when E0 is the only code displayed.

If a customer or technician initiated the diagnostic mode to investigate an ice production complaint but receives only E0, the issue may be an intermittent condition that has since resolved, a non-electrical cause such as a kinked water supply line or inadequate freezer temperature, or user expectation mismatch regarding ice output volume. Further investigation should focus on environmental and mechanical factors rather than electrical faults.

Source: manufacturer service documentation.

Common causes of E0

  1. 01

    Normal diagnostic mode result

    Wiring / connection

    E0 appears after a manual diagnostic test is run and no faults are detected. This is the expected outcome when all ice maker components are working correctly.

  2. 02

    Intermittent issue that has cleared

    Wiring / connection

    A fault that occurred previously may have resolved on its own, leaving no stored error code. If ice production problems persist, additional observation or repeated diagnostic cycles may be needed.

  3. 03

    Inadequate freezer temperature

    Wiring / connection

    If ice production is low but E0 is displayed, the freezer may not be maintaining a cold enough temperature for efficient ice making, which is a mechanical or sealed system issue rather than an ice maker electronics fault.

  4. 04

    Restricted water supply

    Wiring / connection

    A partially closed supply valve, kinked line, or clogged water filter can limit ice production without triggering an electrical fault code. Inspect the water supply path and filter condition.

See the test procedure for each cause

Frequently asked questions about E0

What does E0 mean on a Maytag refrigerator?
E0 on a Maytag refrigerator ice maker indicates no errors are present and the ice maker is functioning normally. It appears during the ice maker diagnostic mode as confirmation that the system's self-check found no faults. This is a status code, not a warning or failure code. No repairs are needed when E0 is the only code shown.
How do I fix the E0 code on my Maytag refrigerator?
No fix is needed for an E0 code because it indicates normal operation. If you are seeing E0 but still experiencing ice production issues, the cause is likely not an electrical fault. Check your water supply line, water filter, and freezer temperature as starting points for further diagnosis.
Is the E0 code on a Maytag refrigerator a safety concern?
No, E0 is not a safety concern. It is a diagnostic status indicator confirming that the ice maker has passed its self-check with no detected faults. There is no risk to the appliance, food, or household when this code is displayed.
How much will it cost to repair an E0 code on a Maytag refrigerator?
Because E0 indicates no fault is present, there is typically no repair cost associated with this code. If a technician visit was initiated to investigate an ice production problem and E0 was the result, you may only incur a diagnostic service call fee, which generally ranges from $75 to $150 depending on the service provider and region.
Will resetting my Maytag refrigerator clear the E0 code?
E0 is a status indicator that appears during a diagnostic test cycle rather than a persistent fault code requiring a reset. Exiting the diagnostic mode will return the display to its normal state. Since E0 indicates no errors, there is nothing to clear.

Related Maytag refrigerator codes

All Maytag refrigerator codes
View all 26 Maytag refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass