mypros+
Error code reference

Midea Refrigerator Error Code CA

Ice-flipping fault of freeze ice maker.

Midea codesMidea refrigerator codes

Ice-flipping fault of freeze ice maker.

First step from the service manual

Check whether the connection terminals on the ice maker and the main PCB are plugged in place and whether there are foreign matters in them; after cleaning the terminals, plug them in again.

The complete diagnostic procedure includes additional test steps, resistance specifications, wiring diagram references, and component test points.

MyPros+ Max

Get the full diagnostic procedure for CA.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What CA means on a Midea refrigerator

The CA error code on a Midea refrigerator indicates an ice-flipping fault within the freeze ice maker system. The ice maker uses a motorized flipping or ejection mechanism to rotate or tip the ice tray, releasing formed ice cubes into the collection bin. When the control system detects that this flipping cycle has failed to complete within the expected timeframe, or that the mechanism is not responding to commands from the main PCB, it logs the CA fault and typically halts ice production to prevent mechanical damage.

The most common origin of this fault is a communication or power delivery breakdown between the main PCB and the ice maker assembly. Loose, corroded, or contaminated connector terminals are a frequent culprit, as any resistance or interruption at the connection points can prevent the flip motor from receiving proper signals or voltage. Ice or frost buildup around the ice maker mechanism can also physically obstruct the flipping arm or tray, causing the motor to stall mid-cycle and triggering the fault.

Secondary causes include a failed ice maker flip motor, a defective position sensor within the ice maker that cannot confirm cycle completion, or a faulty main PCB that is not issuing the correct control signals. Because the diagnostic process starts at the electrical connections, technicians should inspect and clean the terminals thoroughly before condemning any individual component. This rules out the simplest and most common cause before moving on to component-level testing.

Source: manufacturer service documentation.

Common causes of CA

  1. 01

    Loose or dirty connector terminals

    Wiring / connection

    The wiring connectors between the ice maker and the main PCB can work loose or accumulate corrosion and debris, interrupting the control signal or power to the flip motor. Inspect both ends of the connector for bent pins, moisture damage, or foreign material and reseat them firmly after cleaning.

  2. 02

    Ice or frost obstruction in the ice maker

    Wiring / connection

    Ice buildup around the flip arm or ice tray can physically block the ejection cycle, causing the motor to stall and triggering the CA fault. Manually defrost the ice maker compartment and check for any ice bridges or frost accumulation blocking the moving parts.

  3. 03

    Failed ice maker flip motor

    Part replacement

    The motor responsible for rotating or tipping the ice tray can wear out or seize, preventing the flipping action from completing. If the terminals are clean and secure but the motor does not run when commanded, the motor or the entire ice maker assembly likely needs replacement.

  4. 04

    Defective ice maker position sensor

    Part replacement

    The ice maker uses a sensor to confirm that the flip cycle has completed and the mechanism has returned to the home position. A faulty sensor may report an incomplete cycle even when the motor runs normally, keeping the CA fault active.

  5. 05

    Faulty main PCB

    Part replacement

    If the main control board is not sending the correct output signals to the ice maker, the flip motor will not receive a command to operate. This is the least likely cause and should only be considered after all other components and connections have been verified.

See the test procedure for each cause

Frequently asked questions about CA

What does CA mean on a Midea refrigerator?
The CA code on a Midea refrigerator indicates an ice-flipping fault in the freeze ice maker. It means the control board has detected that the mechanism responsible for ejecting ice cubes from the tray did not complete its cycle properly. This could be caused by a loose connection, a physical obstruction, or a failed component inside the ice maker assembly.
How do I fix the CA error code on my Midea refrigerator?
Start by unplugging the refrigerator and locating the connector terminals that link the ice maker to the main PCB. Clean any debris or corrosion from the terminals and firmly reseat the connectors. Also check for any ice or frost buildup that could be physically blocking the flip mechanism and defrost the area if needed. If the code returns after these steps, the flip motor or another internal ice maker component may need to be replaced.
Is the CA error code on a Midea refrigerator a safety concern?
The CA code is not a safety hazard to your home or food supply. It is limited to the ice maker function, and the refrigerator will continue to cool and freeze normally. However, leaving the fault unaddressed will result in no ice production, and in some cases the ice maker may be disabled by the control board until the fault is cleared.
Will resetting my Midea refrigerator clear the CA error code?
A power reset may temporarily clear the CA code, but it will return if the underlying cause has not been corrected. Unplugging the unit for a few minutes and plugging it back in can sometimes allow a one-time successful ice cycle if the fault was caused by a minor glitch. If the code reappears after the reset, a physical inspection of the connections and ice maker mechanism is needed.
How much does it cost to repair a Midea refrigerator CA error code?
If the fix only requires cleaning and reseating the connector terminals, there is no parts cost, and the repair can be done at home at no charge. If the ice maker flip motor or the full ice maker assembly needs replacement, parts and labor costs typically range from roughly 80 dollars to 250 dollars or more depending on your location and whether you hire a technician. Replacing the main PCB, if required, is the most expensive scenario and can push the total repair cost higher.

Related Midea refrigerator codes

All Midea refrigerator codes
View all 22 Midea refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass