mypros+
Error code reference

Miele Washer Error Code F4017

Program has stopped at a permanently programmed program stop.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F4017 error code actually means

Your Miele washer has paused at a built-in stop point within the wash program you selected. This is often intentional and the machine is waiting for you to take some action, like pressing Start to continue. If the pause seems unexpected, try pressing the Start button to see if the cycle resumes normally.

Diagnostic procedure

The full F4017 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F4017 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F4017

Ranked by how often they cause this code
  1. 1Intentional programmed stop in specialty cycle
  2. 2Incorrect program selection
  3. 3Start/Stop button not pressed after a mid-cycle pause
  4. 4Control board irregularity holding program at stop
  5. 5User-initiated pause not cleared

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F4017

What does F4017 mean on a Miele washer?
F4017 indicates that the wash program has stopped at a permanently programmed stop point within the cycle. This can be an intentional design feature in certain Miele programs that require user interaction before continuing. It does not always indicate a fault or component failure. Pressing the Start/Stop button is typically the first step to resume the cycle.
Is it safe to continue using my Miele washer when F4017 appears?
In most cases, yes. F4017 reflects a program stop rather than a safety-critical component failure, so there is no immediate risk to the appliance or household. However, if the machine is holding water inside the drum and will not drain or advance, you should address the issue promptly to avoid leaving laundry sitting in standing water for an extended period.
How much does it cost to repair a Miele washer showing F4017?
If the issue is simply a programmed stop requiring user input, there is no repair cost involved. If a faulty control board is causing the machine to incorrectly halt at this stop point, control board replacement on a Miele washer typically ranges from $200 to $600 or more depending on the model and labor rates in your area. A diagnostic service call from a Miele-authorized technician generally runs between $80 and $150 before any parts are factored in.
How do I fix the F4017 error on my Miele washer?
Start by pressing the Start/Stop button to see if the cycle resumes. If the machine is running a specialty program like wool or hand-wash, check whether that cycle includes a built-in stop requiring your input. If the machine will not continue after pressing Start, try canceling the cycle, selecting a new program, and restarting. Persistent issues that cannot be resolved through these steps may require a technician to inspect the control board.
Will resetting my Miele washer clear the F4017 error?
A power reset by unplugging the machine for a few minutes may clear the error and reset the program logic. However, if the machine was stopped mid-cycle, resetting it this way may cause it to restart from the beginning rather than resuming where it left off. If the error reappears consistently in the same program and at the same point, a reset alone will not resolve the underlying cause.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass