Error code reference

Miele Washer Error Code F4018

Program has stopped at a programmed stop before a spin.

Miele codes Miele washer codes

Program has stopped at a programmed stop before a spin.

MyPros+ Max

Get the full diagnostic procedure for F4018.

Step-by-step tests with expected resistance, voltage, and continuity values
Wiring diagram references and connector pinouts from the OEM service manual
Verified part numbers when replacement is required

Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

M+

M+ Max·Miele Washer

F4018 on my Miele Washer

M+

Program has stopped at a programmed stop before

From Service Manual 662515, p.47:

1.Access service mode to confirm the active fault code and read stored error history.

2.Measure the drive motor winding resistance at the main control connector. Expected: 2 to 6 ohms between winding pairs.

3.Rotate the drum by hand and check for free rotation. Inspect the belt and pulley for glaze or wear; a slipping belt mimics a motor fault under load.

Part W10006384

Drive motor

What F4018 means on a Miele washer

F4018 on a Miele washer indicates that the program has halted at a programmed stop point positioned immediately before a spin cycle. This is a deliberate pause built into certain wash programs rather than a fault caused by a failed component. Miele programs certain cycles, particularly delicates, wools, and hand-wash programs, to stop at this stage so the operator can intervene, manually adjust settings, or remove items that should not be subjected to high-speed spinning. The machine is functioning as designed when this code appears in those contexts.

The stop is triggered by the program sequencer reaching a predefined step in the cycle logic. At this point, the drum rotation ceases and the display presents F4018 to alert the user that input is required before the cycle can continue. The washer is not in an error state in the traditional sense; it is awaiting a deliberate action such as pressing the start button to resume, selecting a reduced spin speed, or choosing to end the cycle without spinning.

If F4018 appears unexpectedly on a program that would not normally include a programmed stop, it is worth reviewing the selected program settings to confirm no accidental stop was programmed via the machine's cycle customization features. Miele washers allow users to save modified program parameters, so a previously saved configuration with a stop enabled could cause this behavior to repeat on subsequent washes.

Source: manufacturer service documentation.

Common causes of F4018

01
Programmed stop in a delicate or wool cycle
Wiring / connection
Miele delicate, wool, and hand-wash programs include a built-in pause before spinning so the user can choose whether to spin and at what speed. This is normal behavior for these programs.
02
User-saved program configuration with stop enabled
Wiring / connection
Miele washers allow customized program settings to be saved. If a stop before spin was enabled and saved in a program preset, it will repeat every time that program is selected.
03
Accidental activation of the stop-before-spin option
Wiring / connection
The stop-before-spin feature can be toggled during program setup. A user may have enabled it unintentionally, causing the pause to occur unexpectedly on a standard program.
04
Program selection error
Wiring / connection
Selecting a program intended for delicates when a standard cotton or synthetic program was intended will introduce cycle steps, including the pre-spin stop, that the user did not anticipate.

See the test procedure for each cause

Frequently asked questions about F4018

What does F4018 mean on a Miele washer?

F4018 means the washer has stopped at a programmed pause point that occurs just before the spin cycle begins. This is a deliberate feature of certain Miele wash programs, particularly those designed for delicate fabrics. The machine is not broken and is waiting for user input to either proceed with spinning or end the cycle.

How do I fix F4018 on my Miele washer?

Press the start button to resume the cycle and allow the spin to proceed. If you do not want the items spun, you can select an end-of-cycle option to drain and stop without spinning. If this pause keeps appearing on programs where you do not expect it, check the saved program settings and disable the stop-before-spin option in the program configuration menu.

Is it safe to continue using my washer when F4018 appears?

Yes, F4018 does not indicate a mechanical or electrical fault. The washer is operating normally and has simply paused as programmed. It is safe to press start to continue the spin or to end the cycle without spinning.

Will resetting my Miele washer clear F4018?

A reset is not needed and will not prevent F4018 from appearing again if the selected program includes a stop before spin. The correct response is to interact with the program at the pause point by pressing start or selecting a spin option. If the stop is the result of a saved program setting, that configuration will need to be changed to prevent recurrence.

Does F4018 require a repair or any replacement parts?

In almost all cases, F4018 does not require any parts or a service call. It is a program-level notification rather than a component failure. If the issue is persistent and you cannot resolve it through program settings, a Miele-certified technician can review the machine's saved configurations, though that scenario is uncommon.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Get the full diagnostic procedure for F4018.

What F4018 means on a Miele washer

Common causes of F4018

Programmed stop in a delicate or wool cycle

User-saved program configuration with stop enabled

Accidental activation of the stop-before-spin option

Program selection error

Frequently asked questions about F4018

Related Miele washer codes