mypros+
Error code reference

Miele Washer Error Code F4060

No door release signal from EFU 235 (signal 2).

Miele codesMiele washer codes

No door release signal from EFU 235 (signal 2).

MyPros+ Max

Get the full diagnostic procedure for F4060.

  • Step-by-step tests with expected resistance, voltage, and continuity values
  • Wiring diagram references and connector pinouts from the OEM service manual
  • Verified part numbers when replacement is required
Get the full procedure

$29/month · Cancel anytime · Or $9.95 3-day pass

What F4060 means on a Miele washer

Error code F4060 on a Miele washer indicates that the control system is not receiving a door release signal from the EFU 235 module (specifically signal 2). The EFU 235 is an electronic relay or interface module responsible for managing door locking and unlocking operations. When the wash cycle completes, the control board sends a command to release the door lock, and the EFU 235 is expected to respond with a confirmation signal. If that signal 2 response is absent or out of specification, the machine flags F4060 and typically keeps the door locked as a safety measure.

This error can stem from a failure within the EFU 235 module itself, a wiring fault between the module and the main control board, or a problem with the door lock assembly that prevents the EFU 235 from completing its signal loop. Connector corrosion, damaged wiring harnesses, or loose terminal connections along the signal path are common contributors. In some cases, the door interlock mechanism may be mechanically seized or electrically open, preventing the EFU 235 from registering a successful release event.

Diagnosis typically involves inspecting the wiring and connectors between the door lock, the EFU 235 module, and the main PCB for damage, corrosion, or poor seating. The EFU 235 module itself should be tested for proper operation and output signals. If wiring integrity is confirmed but the fault persists, the EFU 235 module or the door lock assembly may require replacement.

Source: manufacturer service documentation.

Common causes of F4060

  1. 01

    EFU 235 Module Failure

    Part replacement

    The EFU 235 module itself may have failed internally and is no longer generating signal 2 after a door release command. This is one of the most direct causes of F4060 and requires module replacement if confirmed.

  2. 02

    Wiring or Connector Fault

    Wiring / connection

    Damaged, corroded, or loose wiring between the EFU 235 module and the main control board can interrupt signal 2. Inspect the harness and connectors for corrosion, broken pins, or poor seating.

  3. 03

    Door Lock Assembly Failure

    Part replacement

    If the door interlock mechanism is mechanically seized or has an open electrical circuit, the EFU 235 may be unable to complete the release signal loop. Testing the door lock for continuity and mechanical function can confirm this.

  4. 04

    Main Control Board Communication Issue

    Part replacement

    A fault in the main PCB may prevent it from properly sending the release command or reading the response from the EFU 235. This is less common but should be considered after ruling out the module and wiring.

See the test procedure for each cause

Frequently asked questions about F4060

What does F4060 mean on a Miele washer?
F4060 indicates that the washer's control system is not receiving door release signal 2 from the EFU 235 module. This module handles door locking and unlocking communication. The machine cannot confirm a safe door release, so it locks the door and stops operation. The fault typically points to the EFU 235 module, related wiring, or the door lock assembly.
Can I fix F4060 myself or does it require a technician?
Basic checks such as inspecting wiring connectors and ensuring the door lock harness is firmly seated can be done by a knowledgeable DIYer. However, testing and replacing the EFU 235 module or diagnosing PCB-level faults requires familiarity with Miele's internal components and wiring layouts. A qualified appliance technician is recommended for anything beyond visual inspection.
Is it safe to use my Miele washer with error code F4060 active?
No, you should not attempt to force the door open or bypass the lock. The washer has stopped as a safety precaution because it cannot confirm the door is safe to open. Continuing to use the machine without resolving the fault could damage the door lock mechanism or the EFU 235 module further.
How much does it cost to repair a Miele washer showing F4060?
Repair costs depend on which component has failed. If only wiring or a connector is at fault, costs may be relatively low, primarily covering a service call fee in the range of $80 to $150. Replacing the EFU 235 module or door lock assembly will add parts costs, typically bringing the total to somewhere between $200 and $500 or more depending on parts availability and labor rates in your area.
Will resetting my Miele washer clear the F4060 error?
A power reset may temporarily clear the error display, but F4060 will return if the underlying fault in the EFU 235 signal path has not been resolved. Resetting does not repair damaged wiring, a faulty module, or a defective door lock. The root cause must be diagnosed and corrected for the error to be permanently resolved.

Related Miele washer codes

All Miele washer codes
View all 254 Miele washer codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass