mypros+
Error code reference

Monogram Dishwasher Error Code RINSE ONLY light flashing

Water does not empty out of the Chef's Washer, indicating a drain blockage.

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the RINSE ONLY light flashing error code actually means

The RINSE ONLY light flashing means your Monogram dishwasher tried to drain but could not get the water out of the tub. This is usually caused by a clog in the drain hose, the garbage disposal, or a small fitting near your sink called an air gap. You will need to find and clear the blockage before the dishwasher can run normally again.

Diagnostic procedure

The full RINSE ONLY light flashing procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Check garbage disposal and air gap for blockage; check outlet hose for kinks and sharp bends.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock RINSE ONLY light flashing procedure $9.95

Or subscribe: $29/month for all codes plus Max AI diagnostics, with 70 Max messages a day.

Most common causes of RINSE ONLY light flashing

Ranked by how often they cause this code
  1. 1Garbage disposal blockage or missing knockout plug
  2. 2Kinked or sharply bent outlet hose
  3. 3Clogged air gap fitting
  4. 4Clogged internal filter or sump area
  5. 5Drain pump failure

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about RINSE ONLY light flashing

What does RINSE ONLY light flashing mean on a Monogram dishwasher?
The flashing RINSE ONLY light on a Monogram dishwasher indicates that the appliance detected a drain failure, meaning water is not emptying out of the tub as expected. The control system triggers this indicator when the drain cycle does not complete successfully. The cause is typically a blockage somewhere in the drain path, including the garbage disposal, air gap, or outlet hose.
Is it safe to use my Monogram dishwasher while the RINSE ONLY light is flashing?
You should not continue running the dishwasher while this error is active. Standing water left in the tub from a failed drain can become unsanitary and may lead to odors or residue buildup on dishes and interior surfaces. Running additional cycles without resolving the drain issue will not clear the fault and could place unnecessary strain on the drain pump.
How much does it cost to repair a Monogram dishwasher with a drain error?
If the fix involves clearing a clog from the garbage disposal, air gap, or outlet hose, there may be no parts cost at all, only the time to inspect and clean the components. If the internal filter needs cleaning, that is also a no-cost repair. If the drain pump has failed and needs replacement, you can expect parts and labor costs combined to fall somewhere in the range of $150 to $400 depending on your location and service provider.
How do I fix the RINSE ONLY flashing light on my Monogram dishwasher?
Start by checking the garbage disposal for clogs and confirm the disposal's dishwasher drain knockout plug has been removed. Next, inspect the outlet hose under the sink for kinks or sharp bends and straighten them out. Also clean the air gap fitting at the sink if one is installed. If those steps do not resolve the issue, remove and clean the dishwasher's internal filter basket, and if drainage still fails, the drain pump may need to be tested or replaced.
Will resetting my Monogram dishwasher clear the RINSE ONLY flashing error?
A reset may temporarily clear the indicator, but if the underlying drain blockage has not been resolved, the error will return as soon as the unit attempts to drain again. The correct approach is to identify and clear the blockage first, then run a drain or normal cycle to confirm the unit empties properly before considering the issue resolved.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass