mypros+
Error code reference

Sharp Microwave Error Code EE6

Oven thermistor (1) failure

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the EE6 error code actually means

Your Sharp microwave has detected a problem with one of its internal temperature sensors and has stopped working to keep you safe. The sensor is either broken or has lost its electrical connection, so the microwave cannot monitor its own temperature during cooking. You will need a technician to test and most likely replace the faulty sensor or its wiring.

Diagnostic procedure

The full EE6 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Test oven thermistor (1) resistance per Procedure K (approx. 231 kΩ at 77°F).
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock EE6 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of EE6

Ranked by how often they cause this code
  1. 1Failed oven thermistor (1)
  2. 2Broken or damaged wiring harness
  3. 3Disconnected or corroded connector
  4. 4Heat damage to thermistor or wiring
  5. 5Moisture or contamination intrusion

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about EE6

What does EE6 mean on a Sharp microwave?
EE6 indicates that oven thermistor (1) has been detected as open, meaning the temperature sensor circuit has lost continuity and is not sending a valid signal to the control board. The microwave uses this thermistor to monitor internal cavity temperature, and when the reading is absent, the unit shuts down as a safety precaution. The thermistor itself, its wiring, or a connector in the circuit is the likely source of the fault.
Is it safe to use my Sharp microwave when it shows EE6?
No, the microwave should not be used while EE6 is active. The control board has disabled operation because it cannot monitor cavity temperature, which means there is no reliable safeguard against overheating during a cooking cycle. Continue using the unit only after the fault has been diagnosed and repaired.
How much does it cost to repair a Sharp microwave with an EE6 error?
If the repair is limited to reseating a connector or addressing a loose wiring issue, out-of-pocket costs may be minimal. Thermistor replacement parts typically fall in the range of $15 to $50 depending on the specific model. If professional labor is needed, total repair costs including parts and service time generally range from $80 to $180, though costs vary by region and service provider.
Can I fix the EE6 error myself on a Sharp microwave?
A knowledgeable DIYer can begin by inspecting and reseating connectors in the thermistor circuit, which requires no parts and may resolve the code if a loose connection is the cause. Replacing the thermistor itself is also a straightforward repair if you are comfortable working inside the appliance cabinet. However, microwave interiors contain a high-voltage capacitor that can hold a dangerous charge even when unplugged, so proper discharge procedures must be followed before touching any internal components.
Will resetting the microwave clear the EE6 error code?
Unplugging the microwave for a minute and restoring power may temporarily clear the display, but the EE6 code will return as soon as the control board performs its next diagnostic check if the underlying fault has not been corrected. A reset does not repair a failed thermistor, broken wire, or faulty connector. The root cause must be addressed for the error to stay clear.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass