mypros+
Error code reference

Viking Refrigerator Error Code Power Up Alarm

All temperature indicator lights flash after power is initially plugged in, after a power loss, or if power switch is turned off, indicating the unit…

Viking codesViking refrigerator codes
Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the Power Up Alarm error code actually means

Your Viking refrigerator is flashing its temperature lights to let you know it lost power at some point and has just started back up. This is normal and does not mean anything is broken. Simply press the Alarm Off or Display On button on the control panel to clear the lights and return to normal operation.

Diagnostic procedure

The full Power Up Alarm procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
First diagnostic step
Press Alarm Off or Display On pad to clear the alarm. Note: All settings return to default factory settings after power loss.
Unlock with pass
Unlock with pass
Unlock with pass
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock Power Up Alarm procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of Power Up Alarm

Ranked by how often they cause this code
  1. 1Household power outage
  2. 2Manual power switch toggled off
  3. 3Initial appliance installation
  4. 4Loose or intermittent power cord connection
  5. 5Tripped circuit breaker or GFCI outlet

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about Power Up Alarm

What does Power Up Alarm mean on a Viking refrigerator?
The Power Up Alarm means the refrigerator has detected a power restoration event, such as being plugged in for the first time, recovering from a power outage, or being switched back on after the power switch was turned off. All temperature indicator lights flash to alert the user that the unit needs to be acknowledged. It is a notification alarm, not a fault, and indicates no component failure. Press the Alarm Off or Display On pad to clear it.
Is the Power Up Alarm on a Viking refrigerator a safety concern?
No, the Power Up Alarm is not a safety concern and does not indicate any problem with the refrigerator's cooling system, sealed system, or electronic controls. It is an informational notification built into the control system design. However, if the alarm recurs frequently without an obvious power event, it may be worth checking the power cord connection and the circuit for intermittent issues.
How much does it cost to repair a Viking refrigerator showing a Power Up Alarm?
In most cases, there is no repair cost associated with the Power Up Alarm because it is a standard notification that clears with a button press. If the alarm is appearing due to an underlying electrical issue such as a failing power cord or a problematic circuit, a service call to diagnose and address that issue could range from around 100 to 300 dollars depending on what is found. No parts are needed to clear the alarm itself.
How do I clear the Power Up Alarm on my Viking refrigerator?
Press the Alarm Off pad or the Display On pad on the refrigerator's control panel to immediately clear the alarm and stop the temperature indicator lights from flashing. After clearing the alarm, check your temperature settings because the control board resets all values to factory defaults after any power loss. Re-enter your preferred temperature setpoints if they differ from the factory defaults.
Will resetting the Power Up Alarm on a Viking refrigerator restore my temperature settings?
Pressing the Alarm Off or Display On pad clears the alarm, but it does not restore your previous custom temperature settings. After any power loss, the control board resets all temperature setpoints to factory default values. You will need to manually re-enter your preferred temperature settings after acknowledging the alarm.

Related Viking refrigerator error codes

All Viking refrigerator codes

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass