mypros+
Error code reference

Whirlpool Dryer Error Code F8

UI EEPROM memory is a CRC failure (cycles and price display disabled until diagnostic code is manually cleared).

Avg. service call
$285
National average. Trip fee plus diagnostic plus labor. Before parts.
MyPros+ 3-day pass
$9.95
Same diagnostic steps, on your phone. Start now.
You keep in your pocket
~$275
Even before you buy the part.
Skip the service call. Fix it yourself.
Full procedure unlocks instantly.
Get Started

What the F8 error code actually means

Your Whirlpool dryer is showing F8 because a small memory chip in the control panel has become corrupted and is no longer storing information correctly. As a result, the dryer has disabled cycle selection and certain display features to prevent problems from running on bad data. A technician will need to manually clear this code through a diagnostic procedure, and if it keeps coming back, the control panel board likely needs to be replaced.

Diagnostic procedure

The full F8 procedure

Step 1 is visible so you can confirm you are on the right page. The remaining steps, the ones that tell you whether to actually replace a part, unlock with any pass.

MyPros+ · DiagnosticsStep 1 preview
1
Confirm the fault
Power cycle the unit: switch off the breaker for 60 seconds, then restore power. If the code returns, the fault is persistent and the procedure below isolates the cause.
More steps, wiring diagram references, and verified part numbers
Includes expected resistance and voltage values, connector pinouts, and supersession notes for replacement parts.
Unlock F8 procedure $9.95

Or subscribe: $29/month for unlimited access to all codes plus Max AI diagnostics.

Most common causes of F8

Ranked by how often they cause this code
  1. 1UI Board EEPROM Corruption
  2. 2Power Surge or Voltage Spike
  3. 3Power Interruption During Memory Write
  4. 4Failed or Degraded UI Board
  5. 5Loose or Intermittent UI Board Wiring Connection

Most DIYers save hundreds by diagnosing before ordering parts.

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass

Questions people ask about F8

What does F8 mean on a Whirlpool dryer?
F8 on a Whirlpool dryer indicates a CRC failure in the EEPROM memory on the user interface board. This means the memory chip's stored data failed its integrity check and is considered corrupted. As a result, the dryer disables cycle selection and price display functions until the code is manually cleared through a diagnostic procedure.
Will resetting the dryer clear the F8 error code?
A standard power reset by unplugging the dryer is unlikely to clear the F8 code because it is a stored diagnostic fault tied to the EEPROM's memory state. The code must be cleared manually through the dryer's diagnostic or service mode. Even after clearing, if the underlying EEPROM corruption remains, the code will return during normal operation.
How much does it cost to repair a Whirlpool dryer with an F8 error?
If the issue resolves after manually clearing the code, there may be no parts cost, though a service call to perform the diagnostic clear can range from $75 to $150 depending on your area. If the UI board requires replacement, parts and labor combined typically range from $150 to $350, depending on the specific board and local labor rates. Getting a diagnostic visit from a qualified technician before ordering parts is advisable to confirm the root cause.
Can I fix the F8 error on my Whirlpool dryer myself?
Manually clearing the code through the dryer's diagnostic mode is the first step and does not require parts or advanced technical skills if you can access the procedure. However, if the F8 code returns after clearing, the UI board itself has likely failed and will need to be replaced. Replacing a UI board requires disconnecting the wiring harness and installing a compatible board, which is within reach for experienced DIYers but may warrant a technician for others.
Is it safe to use my Whirlpool dryer with an F8 error code?
The F8 code causes the dryer to disable cycle selection and the price display as a protective measure, which means you may not be able to start or select cycles normally. Attempting to operate the dryer in this degraded state is not recommended until the code is cleared. There is no direct safety hazard such as a fire or electrical risk associated with the F8 code itself, but the dryer's functionality is compromised.

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass