mypros+
Model reference

Admiral MER4351AGW

Range

8 documents37 error codes30 service modes

Available documentation

Tech Sheet

  • Tech Sheet - 160265357 pg
    Covers this model
  • Electric Freestanding Range — Technical Information8 pg
    Covers this model
  • Electric Freestanding Range — Technical Information7 pg
    Covers this model

Service Manual

  • Service Manual - Freestanding Electric Range54 pg
    Covers this model
  • Freestanding Electric Range Service Manual54 pg
    Covers this model
  • Failure Codes and Wiring Diagrams for Maytag Heritage Gas & Electric Ranges124 pg
    Covers this model
  • FAILURE CODES AND WIRING DIAGRAMS for MAYTAG HERITAGE GAS & ELECTRIC RANGES124 pg
    Covers this model

Bulletin

  • Service Pointer - 8178740 (Oven Starts Before Desired Temperature is Selected)2 pg
    Covers this model
MyPros+ Max

Diagnose your Admiral MER4351AGW.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (37)

CodeMeaning
1c1cShorted key detected; a keypress is stuck or shorted.1c2cKeyboard tail disconnected or keyboard loop has improper value.1c31Cancel key circuit problem; cancel key has improper value.1c32Cancel key circuit problem (cancel key improper value) on lower oven cavity.1c4cMicro communication failure; serial communications checksum invalid.1c5cVcc or ground fault detected at testpoint during cook active.1c6cEEPROM error detected.1c7cControl not calibrated; calibration value out of range.1c81Cook profile corrupted in EEPROM for upper/single oven cavity (CRC invalid).1c82Cook profile corrupted in EEPROM for lower oven cavity (CRC invalid).1c8cCooking program error detected during active cook cycle.1d11Runaway oven temperature detected (650°F); sensor resistance greater than 2218…1d12Runaway temperature (650°F) detected with door unlocked on lower oven cavity.1d21Runaway temperature (950°F) detected with door locked on upper/single oven…1d22Runaway temperature (950°F) detected with door locked on lower oven cavity.3d11Oven temperature sensor open; sensor resistance reads infinite ohms3d12Temperature sensor failure (open) on lower oven cavity3d21Oven temperature sensor shorted; sensor resistance reads approximately 0 ohms3d22Temperature sensor failure (short) on lower oven cavity3d41Meat probe shorted3d51Meat probe not calibrated4d11Door switch position failure4d12Door switch position failure4d21No Reverse Airflow Fan rotation (no/low RPM) on upper/single oven cavity.4d22No Reverse Airflow Fan rotation (no/low RPM) on lower oven cavity.4d31Reverse Airflow Fan state error4d32Reverse Airflow Fan state error4d41High Reverse Airflow Fan rotation (high RPM) on upper/single oven cavity.4d42High Reverse Airflow Fan rotation (high RPM) on lower oven cavity.4d51Door switch circuit failure
View all 37 error codes
4d52Door switch circuit failure9d11Door latch will not lock on upper/single oven cavity9d12Door latch will not lock on lower oven cavity9d21Door latch will not unlock on upper/single oven cavity9d22Door latch will not unlock on lower oven cavity9d31Door latch both locked and unlocked simultaneously on upper/single oven9d32Door latch both locked and unlocked simultaneously on lower oven

Service modes (30)

  • 24 Hour Clock Toggle["Press and hold Cancel and Delay pads for 3 to 5 seconds.","Press More + or Less
  • Child Lock Out["Press and hold Cancel and Cook & Hold pads for 3 to 5 seconds until beep sounds."]
  • Clock Display Toggle["Press and hold Cancel and Clock pads for 3 to 5 seconds."]
  • Clock Display Toggle (On/Off)["Press and hold Cancel and Clock pads for 3 to 5 seconds."]
  • Diagnostic Code DisplayPress and hold More + pad for 3 to 5 seconds within 60 seconds of applying power to the control…
  • Diagnostic Code Display Mode["Must be started within 60 seconds of powering up the control.","Press and hold More + pad within…
  • Diagnostic Code Display Mode (H1 Controls)Press and hold AUTOSET pad for 3 seconds at power-up.
  • Diagnostic Code Display Mode (H3 Controls)Press and hold Upper Cancel and Timer for 3 to 5 seconds within 5 minutes of power up.
  • Diagnostic Code Display Mode (NSC Controls)Press and hold the More + pad for 3 to 5 seconds when powering up the unit (within 60 seconds of…
  • Factory Default Reset["Press and hold Cancel and Keep Warm pads for 3 to 5 seconds until beep sounds."]
  • Faults Access (EOC III Controls)1
  • Keypad LockoutPress and hold Cancel and Timer pads for 3 to 5 seconds. Press More + or Less
  • One-Watt Standby ModePress and hold Cancel and Less
  • One-Watt Standby Mode (NSC Controls)Press and hold Cancel and Less
  • Oven Temperature Adjustment1. Press Bake pad. 2. Enter 550 on the digit-pad. 3. Immediately press and hold Bake pad for 3 to 5…
  • Quick Test1
  • Quick Test Mode["Must be entered within the first 5 minutes after power up.","Press and hold Cancel and Broil pads…
  • Quick Test Mode (EOC III Controls)1
  • Quick Test Mode (H1 Controls - Convection Model)1
  • Quick Test Mode (H1 Controls - Non-Convection Model)1
  • Quick Test Mode (H2/H2.5 Controls)1
  • Quick Test Mode (H3 Controls)1
  • Quick Test Mode (M1/M2 Controls)1
  • Quick Test Mode (NSC Non-Self Clean Controls)1
  • Sabbath Mode1
  • Service Mode (EOC III Controls)1
  • Temperature Display (°F/°C toggle)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press More + or Less
  • Temperature Display (°F/°C)Press and hold Cancel and Bake pads for 3 to 5 seconds. Press More + or Less
  • Temperature Display Toggle (°F/°C)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press More + or Less
  • Test Mode (UH Controls)1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Admiral range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass