mypros+
Model reference

Admiral S1078EH-KZ

Range

11 documents39 error codes18 service modes

Available documentation

Service Manual

  • Service Manual - W10670270A76 pg
    Covers this model
  • servicemanual w10881701 l 9164 pg
    Covers this model
  • KitchenAid Job Aid W10807512 - 27 & 30" Built-In Single and Double Wall Ovens52 pg
    Covers this model

Installation Guide

  • Installation Instructions33 pg
    Covers this model
  • Installation Instructions12 pg
    Covers this model
  • Installation Instructions11 pg
    Covers this model
  • Installation Instructions7 pg
    Covers this model
  • Installation Instructions5 pg
    Covers this model
  • Installation Instructions13 pg
    Covers this model
  • Instrucciones de instalacion9 pg
    Covers this model
  • Installation Instructions7 pg
    Covers this model
MyPros+ Max

Diagnose your Admiral S1078EH-KZ.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (39)

CodeMeaning
AFRestricted airflow detected that may affect dryer performance.F1 E0User Interface failureF1 E1Appliance Manager failure.F1E1Motor relay stuck on, indicates an ACU problem.F1E3Incorrect controller installed (electric models only); ACU and/or UI part…F1E5ACU parameter file missing.F2 E0Keypad disconnected from User Interface.F2 E1Stuck or shorted key on keypad.F2E1User Interface stuck button (depressed for over 20 seconds); only appears in…F2E3User Interface and ACU model ID parameter mismatch caused by replacement with…F2E4UI software errorF2E5UI software errorF3 E0Main/upper oven temperature sensor open or shorted.F3 E1Bottom/lower oven temperature sensor open or shorted.F3 E3Meat Probe connector jack or Meat Probe shorted.F3E1Exhaust thermistor is open or shorted; open if temperature drops below 18°F…F3E2Moisture sensor strip is open or shorted; only appears in service diagnostic…F3E3Inlet thermistor is open or shorted; open if temperature drops below 18°F…F3E7Rear moisture sensor strip is open or shorted (Maytag models only); only…F4E1No voltage detected at heater relay 1, indicating a heater failure or connector…F4E2No voltage detected at heater relay 2 (electric models only), indicating a…F4E3Low airflow detected that may affect dryer performance.F4E4Low L2 voltage (less than 50 V) detected at the CCU (electric models only).F4E5Temperature threshold of the dryer has been exceeded, usually indicating poor…F5 E0Door and latch input switches do not agree (main/upper oven).F5 E1Latch not operating (main/upper oven).F5 E3Door and latch input switches do not agree (lower oven).F5 E4Latch not operating (lower oven).F6 E0Oven User Interface lost communication.F6 E1Over temperature condition (main/upper oven).
View all 39 error codes
F6 E3Over temperature condition (lower oven).F6 E4Appliance Manager failure.F6 E6Oven Appliance Manager lost communication (main/upper oven).F6 E9Oven Appliance Manager lost communication (lower oven).F6 EAUser Interface over temperature condition.F6E2Communications errorF6E3Communication errorL2Low L2 voltage (less than 30 V) detected at the ACU.PFPower failure occurred while the dryer was running.

Service modes (18)

  • Adjusting Customer-Focused Dryness Level["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS button for…
  • automatic_diagnostic["Turn the product on.","Within 20 seconds of Power On, press and hold the Clean button first, then…
  • Cavity Size SelectEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • cavity_size_selectPress CANCEL > CANCEL > START to enter Diagnostic Mode
  • clean_mode["Press ON/OFF button to stop ice production.","Wait 10 minutes for ice to fall into storage bin
  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS button for…
  • diagnosticPress CANCEL, then CANCEL, then START.
  • Diagnostic ModePress CANCEL, then CANCEL, then START.
  • Error Code Review and ClearEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • error_code_review_and_clearEnter Diagnostic Mode (CANCEL > CANCEL > START), then press keypad 3 or 6 to scroll to the error…
  • Fault Code Display / Clear["1. Activate Service Diagnostic Mode first.","2. Press and release the 3rd button used to activate…
  • Key Activation & Encoder Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • manual_diagnostic["Turn the product on.","Within 20 seconds of Power On, press and hold the Clean button first, then…
  • Relay ActivationEnter Diagnostic Mode (CANCEL > CANCEL > START)
  • relay_activationEnter Diagnostic Mode (CANCEL > CANCEL > START), then press keypad 3 or 6 to scroll to the RELAY…
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Test Mode["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate the…
  • Software Version Display["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate the…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Admiral range models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass