mypros+
Model reference

Amana 100D-2MA

Air Conditioner

1 document69 error codes21 service modes

Available documentation

Tech Tip

  • Instruction Sheet8 pg
    Covers this model
MyPros+ Max

Diagnose your Amana 100D-2MA.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (69)

CodeMeaning
d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord6Coin 2 error (dryer)d9Low voltage detection errorF0 E0No fault code (default)F0-E0Default code indicating no fault present.F01Dryer motor control circuit errorF03Accelerometer failureF04Accelerometer failureF1 E0Electronic control module failure (E0, E1, E2 variants).F1 E1Electronic control module failure.F1 E2Electronic control module failure.F1 E3Electronic control module failure (E3, E4, E5 variants).F1 E4Electronic control module failure.F1 E5Electronic control module failure.F1-E0Electronic control module failure.F1-E1Electronic control module failure.F1-E2Electronic control module failure.F1-E3Electronic control module failure.F1-E4Electronic control module failure.F11Motor Control Unit (MCU) has a failure, possibly due to repeating under or…F2 E0Keypad not connected.F2 E1Keypad not connected.F2 E3Sustained key press or short circuit on keypad.F2-E0Keypad not connected.F2-E1Keypad not connected.F2-E2Prolonged key press or short circuit on keypad.F20No water detected entering washerF21Long drain
View all 69 error codes
F22Door lock errorF23Dryer exhaust thermistor shorted errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between washer CCU and MCU.F29Door unlock errorF3 E0Lower oven temperature sensor open circuit.F3 E1Lower oven temperature sensor short circuit.F3 E2Microwave oven temperature sensor open circuit.F3 E3Microwave oven temperature sensor short circuit.F3-E0Lower temperature sensor open circuit.F3-E1Lower temperature sensor short circuit.F3-E2Microwave temperature sensor open circuit.F3-E3Microwave temperature sensor short circuit.F31Overheating of motorF33Pump disconnectedF34Load detected in washer during washer cleanout cycle.F5 E0Excessive temperature in lower cavity during self-clean cycle.F5-E0Excessive temperature in lower cavity during self-clean cycle.F6 E0Excessive temperature in lower cavity during cooking.F6 E1Excessive temperature in microwave oven during cooking.F6-E0Excessive temperature in lower cavity during bake mode.F6-E1Excessive temperature in microwave oven during cooking.F70Dryer communication failure from dryer CCU to UICF71Dryer communication failure from UIC to dryer CCUF73UIC failureF74Dryer UIC EEPROM errorF8 E0Self-clean latch unable to lock.F8 E1Self-clean latch unable to unlock.F8 E2Excessive oven temperature with door open and latch locked.F8 E3Excessive oven temperature with door open and latch unlocked.F8 E4Excessive oven temperature with door closed and latch unlocked.F8-E0Self-clean latch unable to unlock.F8-E1Self-clean latch unable to unlock.F8-E2Excessive temperature in oven with door open and latch locked.F8-E3Excessive temperature in oven with door open and latch unlocked.F8-E4Excessive temperature in oven with door closed and latch unlocked.

Service modes (21)

  • Default fault code displayPress and hold UPPER OFF button for 5 seconds
  • Fault code displayPress and hold the UPPER OFF button for 5 seconds.
  • Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message 'dAS' will appear in the…
  • Help Mode (PD Models)["Open the service door.","Press the EXTRA RINSE washer keypad until display reads 2.XX.","Press…
  • Microwave power output test1
  • P-01 Cancel Cycle, Reset Errors, and Clear Escrow["Enter Service Diagnostic Test Mode.","Press START after 'P-01' is displayed."]
  • P-02 Cycle Credit["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-02' is displayed.","Press…
  • P-03 Quick Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-03' is displayed.","Press…
  • P-04 Manual Overview Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-04' is displayed.","Press…
  • P-05 Button Test["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-05' is displayed.","Press START…
  • P-06 Drain and Spin["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-06' is displayed.","Press…
  • P-07 UI Diagnostics["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-07' is displayed.","Press…
  • P-08 Clean Washer Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-08' is displayed.","Press…
  • P-10 Dryer Diagnostic Cycle["Enter Service Diagnostic Test Mode.","Press EXTRA RINSE until 'P-10' is displayed.","Press…
  • Sabbath modeSabbath mode is indicated by 'SAB' symbol on the display.
  • Service Diagnostic Test Mode["Enter service mode (setup mode) so the display shows either 6.xx code, cycle count, money count…
  • Set-up Mode["PD/PN/PR Models
  • Setup Mode["PD/PR Models
  • Temperature display toggle (Fahrenheit/Celsius)Press and hold the BROIL button for 5 seconds
  • Temperature offset calibrationAdjust temperature offset in increments of 3°C or 5°F
  • Temperature unit conversion (F/C)Press and hold the BROIL button for 5 seconds to switch to Celsius (indicated by 'C' on display).

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax