Model reference
Amana 212D-3J
Air Conditioner
30 error codes9 service modes
MyPros+ Max
Diagnose your Amana 212D-3J.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (30)
CodeMeaning
E0No errors; functioning ice maker.E1No cooling; ice maker timed out; ice compartment unable to reach desired…E2Motor lost position; ice maker did not find home during harvest and exceeded…E3Heater time-out; ice mold heater was on longer than maximum allowable time…E4Ice bin not present or full (manufacturing error code).E5Bad ice maker thermistor; ice storage temperature satisfied but ice mold in…E6Dispenser UI EEPROM faulty (manufacturing error code).ErCommunication failure (manufacturing error code).F0E0No fault present.F0E2Over suds condition detected; suds prevent the basket from spinning up to speed…F0E4High water temperature detected during rinse cycle (105°F or higher).F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the motor control section of the main control.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Switch mismatch; the switches do not match the console or are not operating…F3E1Pressure system fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open, or control not…F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed fault; main control cannot determine speed of basket, or speed…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; indicates an open clockwise or counterclockwise circuit of the…F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill or long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…Service modes (9)
- Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Spin LED is On (all others…
- Calibration Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse LED is On (all others…
- Fault Code Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Done LED is On (all others…
- Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Spin and Done LEDs are On…
- Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off). Wait 10 seconds after…
- Service Diagnostics Mode["Ensure refrigerator is not in lockout mode.","Press SW1 and SW2 simultaneously for 3…
- Software Version Display Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse, Spin, and Done LEDs…
- Tachometer Verification Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Wash and Done LEDs are On…
- UI Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until Rinse and Spin LEDs are On…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana air conditioner models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass