mypros+
Model reference

Amana 5P-2NM

Air Conditioner

2 documents27 error codes20 service modes

Available documentation

Tech Sheet

  • techsheet w10280489 revd48 pg
    Covers this model

Tech Tip

  • Instruction Sheet - 818468812 pg
    Covers this model
MyPros+ Max

Diagnose your Amana 5P-2NM.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (27)

CodeMeaning
:Power failure indication; the colon flashes on the display after a power…F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the main control board.F2Membrane switch failure.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and User Interface; UI identification does not match…F3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F3HHumidity sensor failure.F4E4Humidity sensor error.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F6Microwave relay failure.F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill or long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…

Service modes (20)

  • Automatic Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • automatic_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Spin' LED is…
  • calibration["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Rinse' LED is…
  • Calibration Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • diagnostic (service diagnostic test modes entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Diagnostic / Test Mode["Plug in microwave oven or reconnect power.","Press Cancel button to enter Standby mode (colon ':'…
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • fault_code_display["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Done' LED is…
  • Manual Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • manual_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' and 'Done' LEDs are…
  • Self-Diagnostic Test Mode["Press and hold CANCEL/OFF while opening the door.","While still holding the CANCEL/OFF button…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • sw_version_display["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse', 'Spin', and 'Done'…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • tachometer_verification["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash' and 'Done' LEDs are…
  • Touch Panel and Electronic Control Self-Diagnostic Test Mode["Press and hold the OFF/CANCEL button while opening the door.","While still holding the OFF/CANCEL…
  • Touch Panel and Microcomputer Board Self-Diagnostic Test["Depress the CANCEL button while opening the door.","While still depressing the CANCEL button…
  • UI Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • ui_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' and 'Spin' LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass