mypros+
Model reference

Amana 8P-5J

Air Conditioner

60 error codes19 service modes
MyPros+ Max

Diagnose your Amana 8P-5J.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (60)

CodeMeaning
drnDrain pump system problemE0No errors, functioning ice maker.E1No coolingE2Motor lost positionE3Heater time-outE4Dry cycleE5Ice maker thermistor is badF0E2Oversuds condition detectedF0E3Overload conditionF0E4Spin limited by water temperatureF0E5Off balance load condition detected.F1Internal H.V./L.VF1E1Main control fault (internal ACU failure).F1E2Motor control section of the main control has faulted.F1E3Mismatch of ACU and UIF2Internal H.V./L.VF2E1UI stuck buttonF2E3UI mismatchF2E4UI software errorF2E5UI software errorF3Internal H.V./L.VF3E1Pressure system faultF3E2Inlet water temperature faultF3E5Indicates that both the compressor and outlet thermistors are open; will occur…F3E6Indicates the moisture sensor strip is open; only appears in service diagnostic…F3E7Indicates that the moisture sensor strip has shorted; only appears in service…F3E8Indicates that the compressor sensor is open; this fault code will stop the…F3E9Indicates that the compressor sensor has shorted; this fault code will stop the…F4Internal H.V./L.VF4E1Heater stuck on
View all 60 error codes
F4E2Heater not turning onF4E3Indicates low air flow that may affect dryer performance.F4E4Indicates low L2 voltage (less than 50V) detected at the CCU.F5Touch panel failure.F5E1Lid switch faultF5E2Lid lock will not lock or lid lock failure.F5E3Lid lock will not unlock.F5E4Lid not opened between cyclesF6Internal H.V./L.VF6E1Communication error between the UI and CCU has not been detected.F6E2Communication errorF6E3Communication errorF7E0Loss of powerF7E1Loss of power during spinF7E2Motor drive module failureF7E3Basket engaged during washF7E4Basket re-engagement failureF7E5Shifter failure.F7E6Motor circuit openF7E7Motor unable to meet target RPM.F7E8Motor over temperatureF7E9Locked rotorF8E1Long fillF8E3Overflow or flood conditionF8E6Water hazardF9E1Drain pump system problemF9E2Drain pump system problemL2Low L2 voltage (less than 50V) detected at the CCU.LFLong fillPFPower failure occurred while the dryer was running.

Service modes (19)

  • Control Panel Deactivation (RCS10MP P1140412M / RCS10MPS P1324901M)["Open oven door, and close oven door.","Press TIME ENTRY pad.","Press 1, 3, 5, and 7 pad in…
  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS LEVEL button…
  • Fault Code Display / Clearing["Enter Service Diagnostic Mode.","If saved fault code exists, it will be flashing in the display…
  • Install Diagnostics["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Key Activation & Encoder Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds, press…
  • Programming mode (RCS10 P1140411M)["Open oven door.","Press and hold pad 1 for approximately 15 seconds.","Signal sounds and display…
  • Programming mode (RCS10MP P1140412M / RCS10MPS P1324901M)["Open oven door.","Press and hold pad 1 for approximately 15 seconds.","After 15 seconds, signal…
  • Programming mode (RFS9B, RCS10, RCS10MP, RCS10MPS, RFS10S, RFS12MPS, RFS12S - 2000/2002 models)["Open oven door.","Press and hold pad 1 for approximately 5 seconds.","After 5 seconds, signal…
  • Service Calibration["Enter Service Test Mode.","Select function number 052 using Soil Level/Temp buttons or cycle…
  • Service Diagnostic Mode["Ensure washer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostics (Automated Test Cycle)["Enter Service Test Mode.","Select function number 051 using Soil Level/Temp buttons or cycle…
  • Service Diagnostics Mode["Ensure refrigerator is not in lockout mode.","Press SW1 and SW2 simultaneously for 3…
  • Service Test Mode (Load Control)["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Software Version Display["First activate Service Diagnostic Mode.","Press and hold the 2nd button used to activate Service…
  • User Interface Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • User Options mode (RCS10MP P1140412M / RCS10MPS P1324901M)["Open oven door.","Press and hold pad 1 for approximately 15 seconds.","Press hidden…
  • User Options mode (RFS10SW2, RFS12SW2)["Open oven door.","Press and hold pad 2 for approximately 5 seconds.","After 5 seconds, signal…
  • User Options mode (RFS9B, RCS10, RCS10MP, RCS10MPS, RFS10S, RFS12MPS, RFS12S - 2000/2002 models)["Open oven door.","Press and hold pad 2 for approximately 5 seconds.","After 5 seconds, signal…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass