Model reference
Amana EPCG3612-1B/P67470-3C
Air Conditioner
3 documents40 error codes20 service modes
Available documentation
Tech Tip
- Instruction Sheet - 818463712 pg
- Instruction Sheet10 pg
- Instruction Sheet - 818546912 pg
MyPros+ Max
Diagnose your Amana EPCG3612-1B/P67470-3C.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax
Error codes (40)
CodeMeaning
:Flashing colon indicates a power failure has occurred.E1Thermistor is open (open circuit detected).E2Thermistor has shorted (short circuit detected).E3User interface keyswitch or software mismatch between the control…F-01Primary control failure.F-02Stuck button or user interface mismatch (only appears in diagnostic test mode).F-22Exhaust thermistor is open.F-23Exhaust thermistor has shorted.F-26Motor drive system failure.F-28Moisture sensor strip is open (only appears in diagnostic test mode).F-29Moisture sensor strip has shorted (only appears in diagnostic test mode).F1-E0Sensor out of range.F1-E1Board thermistor open or short-circuited.F1-E2WIDE queue full.F1-E9EEPROM communication error.F1E1Primary control failure.F2Touch panel failure.F2-E0Keypad disconnected.F2-E1Stuck key.F2-E2Cancel key error.F2-E5Cancel key error (variant).F2-E7Cancel key error (variant).F2E1Stuck button or user interface mismatchF3-E0Main oven sensor open or short-circuited.F3-E2Warming drawer sensor open or short-circuited (on some models).F3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF3HHumidity sensor failure.View all 40 error codes
F3TTemperature sensor failure.F4E4Low line voltage detected.F5-E0Door and door switches mismatch.F6MW relay (Relay 4903) failureF6-E1Bake excessive temperature.F6-E2Warming drawer excessive temperature.F7Power to magnetron interrupted.NTC OPEN, CALL FOR SERVICEHood thermistor is open.NTC SHORT, CALL FOR SERVICEHood thermistor is shorted.PFPower failure occurred while the dryer was running.
Service modes (20)
- Auto TestAfter entering service mode (CANCEL>CANCEL>START), press the up arrow, '+' or '3' key to scroll to…
- Console Diagnostics (within Diagnostic Test Mode)["Enter Diagnostic Test Mode as described above.","Press each button or turn the cycle selector to…
- Customer-Focused Drying Mode Adjustment1
- Diagnostic Test Mode1
- Diagnostic: Door Switch (within Diagnostic Test Mode)["Enter Diagnostic Test Mode.","Open the dryer door
- Diagnostic: Moisture Sensor (within Diagnostic Test Mode)["Enter Diagnostic Test Mode.","Locate two metal strips on the face of the lint screen…
- DISPLAYFrom service mode, scroll to step 5 (DISPLAY).
- Dryness Adjust Mode (TEST #4a)1. Activate the diagnostic test mode and advance past saved fault codes. 2. Press and hold the…
- ENG MODEFrom service mode, scroll to step 2 (ENG MODE)
- FAULTSFrom service mode, scroll to step 7 (FAULTS).
- MRC2 Diagnostic/Service ModePress CANCEL > CANCEL > START
- RELAY USAGEFrom service mode, scroll to step 8 (RELAY USAGE).
- Self-diagnostic test mode["1
- Service Diagnostic Mode1
- Temperature Offset AdjustmentPress and hold OVEN LIGHT for 5 seconds
- TEST MODE (Relay Control)From service mode, scroll to step 3 (TEST MODE)
- TEST ON (Relay Control from entry)Displayed immediately upon entering service mode (CANCEL>CANCEL>START)
- USAGEFrom service mode, scroll to step 1 using up arrow/'+'/3 key.
- User Interface/Control System TestFrom within Service Diagnostic mode, press and release the 1st button used to enter Service…
- VERSIONFrom service mode, scroll to step 4 (VERSION).
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana air conditioner models
75,000+ service documents · 20,000+ error codes · 100+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax