mypros+
Model reference

Amana EPCG6017-3C/P67470-21C

Air Conditioner

41 error codes25 service modes
MyPros+ Max

Diagnose your Amana EPCG6017-3C/P67470-21C.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (41)

CodeMeaning
2EVoltage for motor control bus is over or under specified limit.3EOver Current is detectedbEMotor tach signal exists without motor running (tach signal exists without…dcNever exceeded 400 rpm due to an unbalanced load during final spin.dLOpen door lock switch with motor running.dSDoor switch is read as open and the door locked switch is read as locked.E0Keypad not connected, or key held down too long, or key is shortedE1Temperature sensor opened (when displayed on upper/left side) or temperature…E2A key is sensed to be pressed more than 30 seconds; the key will be assumed to…E3Machine control is attempting to drive the motor but is not seeing any tach…ERRORDisplayed when the AH (Absolute Humidity) sensor bridge circuit cannot be…F0Default F codeF1Electronic control malfunction (when E code is not E3); or keypad not connected…F1.E1Relay control board defective.F2Keyboard (membrane switch) failure.F2.H1Hood keys stuck.F2.H2Hood/light switch defective.F2.Q1Not reading keypad inputs.F3Temperature sensor opened (E0) or temperature sensor shorted (E1).F3.H1Humidity sensor failure.F3.T1UIB (user interface board) thermistor failure.F3.T2FC (forced convection) thermistor failure.F3.T4Magnetron thermistor failure.F3HHumidity sensor failure.F3TTemperature sensor failure (oven temperature out of valid range).F5Oven temperature too highF6MW (microwave) relay failure.F7Interrupted operation (possible magnetron overtemperature protection triggered…F9Relay control board communications error.F9.QTouch communication error between UIB and touch panel board.
View all 41 error codes
FLDoor failed to lock after 3 attempts.HrHeater Relay failure.LEWater sensor level faultLODoor failed to unlock after 3 attempts.ndThe water level fails to drop below the Low Water level reset within 15…nFContinuous fill of 12 minutes or total fill of 14 minutes detected.odThe door has not been opened after two complete wash cyclesOEA fault is detected in the water level sensorSrSystem Relay failureSudSWasher is in a suds period in the cycle; displayed instead of time remaining.tEAbnormal high/low temperature or ohm resistance seen from sump thermistor.

Service modes (25)

  • AH Sensor Control Unit Test (with dummy resistor circuit)["Disconnect power supply cord.","Remove cabinet.","Open door and block it open.","Discharge high…
  • AH Sensor Diagnostic Test (Water Load Cooking Test)["Ensure oven has been plugged in at least 2 minutes before testing.","Fill approximately 200 ml…
  • AH Sensor Water Load Cooking Test (Diagnostic Sensor Test)["Ensure oven has been plugged in at least 2 minutes.","Ensure cabinet is installed and screws…
  • Board Input TestWhile in Service Mode, press the Spin Only key
  • Board Output TestWhile in Service Mode, press the Spin Speed key.
  • Child Lockout / Keypad Disable Mode["Press the OFF/CANCEL key for 5 seconds."]
  • Control Unit AH Sensor Dummy Resistor Test["Disconnect power supply cord.","Remove cabinet.","Open door and block it open.","Discharge HV…
  • Defrost Center Test["Open the oven door.","Place one cup of water in the center of the turntable tray.","Close the…
  • demo_mode["On the Main Menu, touch 'Settings & Info.'","On Settings & Info screen, touch 'Demo Mode.'","The…
  • diagnostic["Unplug microwave oven or disconnect power.","Open the microwave oven door.","Press and hold…
  • Diagnostic Code DisplayWhile in Service Mode, press Rinse & Spin key (display shows 'd'), then rotate Rotary Cycle…
  • Display Diagnostic CodesWhile in Service Mode, press Rinse & Spin key (display shows 'd'), then rotate Rotary Cycle…
  • Electronic Oven Control Test["1. Unplug the oven.","2. Remove the cabinet.","3. Discharge the HV capacitor with a 20,000 ohm…
  • Fast Time Down TestWhile in Service Mode and while any test or cycle is running, press Wash/Rinse Temp key to advance…
  • Key Unit Test["Disconnect power supply cord.","Open door and block it open.","Discharge HV capacitor (wait 60…
  • learning_mode["Oven must be off.","On the Main Menu, touch 'Settings & Info.'","On Settings & Info screen, touch…
  • LED/Switch TestWhile in Service Mode, press the Delay key for 3 seconds, then press individual buttons to test
  • Quick Service CycleWhile in Service Mode, press Wash/Rinse Temp and Soil Level keys for 3 seconds
  • Quick Spin TestWhile in Service Mode, press Delay and Rinse & Spin keys.
  • Relay Test["Disconnect power supply cord.","Remove unit from wall and remove cabinet.","Open door and block…
  • Sales Demonstration Mode (Demo Mode)["Press and hold the TIMER keypad until a small 'd' appears on the display (approximately 5…
  • Service Mode1
  • Touch Panel Self-Test / Microcomputer Board Test["Ensure power is connected and the door is closed.","Press and hold the CANCEL/OFF keypad.","Open…
  • Touch Panel Self-Test Mode["Ensure power is connected and the door is closed.","Press and hold the CANCEL/OFF keypad.","Open…
  • Water Load Sensor Cooking Test (AH20)["Ensure oven has been plugged in at least 2 minutes.","Fill approximately 200 milliliters (7.2 oz)…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax