mypros+
Model reference

Amana ES213-2MK/P67535-3R

Air Conditioner

81 error codes44 service modes
MyPros+ Max

Diagnose your Amana ES213-2MK/P67535-3R.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (81)

CodeMeaning
1c1cShorted key detected; a key is stuck or shorted on the control board.1c2cMembrane keyboard disconnected.1c31Cancel key circuit problem; cancel key returning improper value.1c32Cancel key circuit problem (lower oven).1c4cMicro communication failure; serial communications checksum invalid.1c5cVcc or ground fault at testpoint on the control circuit board.1c6cEEPROM error detected on the control board.1c7cControl not calibrated; calibration value out of range.1c81EEPROM CRC error1c8cCooking program error detected during active cook cycle.1d11Runaway oven temperature detected (650°F); sensor resistance greater than 2218…1d12Runaway temperature (650°F) with door unlocked in lower oven cavity; sensor…1d21Runaway oven temperature (950°F) detected with door locked; sensor resistance…1d22Runaway temperature (950°F) with door locked in lower oven cavity; sensor…3d11Temperature sensor open circuit; sensor resistance reads infinite Ohms.3d12Temperature sensor open (lower cavity); sensor resistance reads infinite.3d21Temperature sensor shorted; sensor resistance reads 0 Ohms.3d22Temperature sensor shorted (lower cavity); sensor resistance reads 0 ohms.3d41Meat probe shorted.3d51Meat probe not calibrated.4d11Door position switch not closed when door is locked during clean cycle.4d21No cooling fan rotation.4d31Cooling fan on when de-energized.4d41Cooling fan overspeed.4d51Door switch circuit failure; door switch reading neither open nor closed.9d11Latch will not lock; lock switch not closed when clean is activated.9d12Door latch will not lock (lower cavity); lock switch not closed.9d21Latch will not unlock; lock switch reads closed when clean is not activated.9d22Door latch will not unlock (lower cavity); unlock switch not closed.9d31Unlock state unknown; both locked and unlocked switches indicate active…
View all 81 error codes
9d32Latch state unknown9d41Unlock state unknown; neither locked nor unlocked switch indicates active.9d42Latch state unknownF0-E0Default F codeF1Internal board failure / A/D Error(s).F1-E0Electronic control malfunction (E0 variant).F1-E1Electronic control malfunction (E1 variant).F1-E2Electronic control malfunction (E2 variant).F1-E3Electronic control malfunction (E3 variant).F1-E4Electronic control malfunction (E4 variant).F1-E5Electronic control malfunction (E5 variant).F1E0Internal board failure / A/D error.F1E1Internal board failure / A/D error.F1E2Internal board failure / A/D error.F2Shorted key on the control panel.F2-E0Keypad keytail not connected.F2-E1Keypad keytail not connected.F2-E3Key held down too long, or key is shorted.F2E0Shorted key detected on the control keypad.F2E1Stuck button or user interface mismatchF3Oven sensor opened, oven sensor shorted, BAKE/BROIL range over temperature, or…F3-E0Temperature sensor opened (lower cavity).F3-E1Temperature sensor shorted (lower cavity).F3-E2Temperature sensor opened (microwave).F3-E3Temperature sensor shorted (microwave).F3E0Oven temperature sensor opened (open circuit).F3E1Oven temperature sensor shorted.F3E2Bake/Broil range over temperature condition.F3E3Clean range over temperature condition.F3E5Second moisture sensor strip is open or shorted (Quad Sense models only; only…F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4-E0Function not used.F5Door and switches do not agree (Clean mode) or door latch not operating (Clean…F5-E0Function not used.F5E0Door and door position switches do not agree during Clean mode.F5E1Door latch not operating during Clean mode.F5E2Door and door position switches do not agree during Clean mode.F6-E0Function not used.F6-E1Microwave cavity over temperature during cooking.F6E1ACU and HMI have not communicated for a specified amount of time.F6E2WiFi Module has not responded for a specified amount of time.F8-E0Function not used.F8-E1Function not used.F8-E2Function not used.F8-E3Function not used.F8-E4Function not used.F9Miswired house or miswired range.F9E0Miswired house or miswired cooker power supply.FCE1WiFi Module communications lost.PFA power failure occurred while the dryer was running.

Service modes (44)

  • 24 Hour Clock Toggle["Press and hold UPPER CANCEL and DELAY pads for 3 seconds."]
  • 24-hour Clock TogglePress and hold Cancel and Delay pads for 3 to 5 seconds. Press More + or Less
  • Beeper Volume Adjustment["Hold UPPER CANCEL and MORE+ pads for 3 seconds."]
  • Child Lock Out["Press and hold UPPER CANCEL and COOK & HOLD pads for 3 seconds.","'OFF' will display where the…
  • Child LockoutPress and hold Cancel and Cook & Hold pads for 3 to 5 seconds until beep sounds.
  • Clock Display TogglePress and hold Cancel and Clock pads for 3 to 5 seconds.
  • Component Activation / Quick Service Cycle (LCD in Door Models)["Enter Service Diagnostic Mode (LCD in Door) first.","From the DIAGNOSTICS HOME screen, scroll…
  • Control LockoutPress the Back and Setup pads simultaneously for 5 seconds to lock.
  • Control ResetPress and hold the Back and Enter pads for 5 seconds to enter SERVICE menu options
  • Customer-Focused Drying Mode Adjustment1
  • Demo ModePress the Setup pad, then press the right ATM pad until DEMO displays
  • Diagnostic Code DisplayPress and hold the More + pad within 5 minutes of powering up the unit. Cycle through the stored…
  • Diagnostic Code Display Mode["Within 60 seconds of powering up the control, press and hold the More + pad for 3 to 5…
  • Diagnostics ModePress CANCEL > CANCEL > START within a 5-second period.
  • Diagnostics Mode (3-digit LCC 90 and LCC 95 Control Display)Press CANCEL 2 times and then START within a 5-second period.
  • Diagnostics Test Mode (All LCC Controls)Press CANCEL 2 times and then START within a 5-second period. Then use individual key presses to…
  • Diagnostics Test Mode (Relay Checks)After entering Diagnostics Mode (CANCEL>CANCEL>START), press individual keys to test relays
  • Display TestPress and hold the Back and Enter pads for 5 seconds to enter SERVICE menu options
  • Factory Default ResetPress and hold Cancel and Keep Warm pads for 3 to 5 seconds until beep sounds.
  • Faults AccessPress and hold the Back and Enter pads for 5 seconds to enter SERVICE menu options
  • Hidden fault code displayPress and hold UPPER OFF key for 5 seconds
  • Key Activation & Encoder Test (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • Keypad Lockout["Press and hold Cancel and Timer pads for 3 to 5 seconds.","Press More + or Less
  • Lower Oven Temperature Adjustment["Press Lower Bake pad.","Enter 550 on the digit-pad.","Immediately press and hold Lower Bake pad…
  • One-Watt Standby Mode["Press and hold Cancel and Less
  • Oven Temperature Adjustment["Press Bake pad.","Enter 550 on the digit-pad.","Immediately press and hold Bake pad for 3 to 5…
  • Quick Test1
  • Quick Test Mode1
  • Quick Test Mode (Non-Self Clean Control)["Must be entered within 5 minutes of power-up.","Press and hold Cancel and Broil pads…
  • Sabbath Mode["Initiate desired bake function before entering Sabbath mode.","Hold Clock pad for 3 to 5 seconds…
  • Service Diagnostic Mode1
  • Service Diagnostic Mode (Console Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Select any three (3)…
  • Service Diagnostic Mode (LCD in Door Models)["Ensure the dryer is in standby mode (plugged in with all indicators off).","Open and close the…
  • Service ModePress the Setup pad, then press the right ATM pad until SERVICE displays
  • Service Test Mode (Console Models)["Activate Service Diagnostic Mode first.","Press and release the 2nd button used to activate…
  • Software Version Display (Console Models)["Activate Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • Software Versions AccessPress and hold the Back and Enter pads for 5 seconds to enter SERVICE menu options
  • Temperature Adjustment1
  • Temperature Adjustment (All LCC Controls)Step 1
  • Temperature Display (°F/°C toggle)["Press and hold Cancel and Bake pads for 3 to 5 seconds.","Press More + or Less
  • Temperature Display Toggle (°F/°C)["Press and hold UPPER CANCEL and UPPER BAKE pads for 3 seconds."]
  • Temperature Display Toggle (F/C)Press and hold Cancel and Bake pads for 3 to 5 seconds. Press More + or Less
  • Upper Oven Temperature Adjustment["Press Upper Bake pad.","Enter 550 on the digit-pad.","Immediately press and hold Upper Bake pad…
  • User Interface/Control System TestFrom within Service Diagnostic mode, press and release the 1st button used to enter Service…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana air conditioner models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax