Model reference
Amana HR2-1B
Air Conditioner
1 document34 error codes25 service modes
Available documentation
Tech Sheet
- Tech Sheet - W10694027 - Rev A (FR)8 pg
MyPros+ Max
Diagnose your Amana HR2-1B.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (34)
CodeMeaning
d13Coin 2 errord16Generation 2 debit card reader errord5Coin 1 errord9Low voltage detection errorF01CCU (Central Control Unit) errorF1-E0EEPROM communication error.F1-E5Sensor out of range.F1-E7Circuit board thermistor open or short-circuited.F1-E9WIDE queue full.F11MCU (Motor Control Unit) has a failure, possibly due to a repeating under or…F2-E0Keypad disconnected.F2-E1Key stuck.F2-E2Cancel key error.F20No water detected entering washerF21Long drainF22Door lock errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionF28Communication failure between CCU and MCU.F29Door unlock errorF3-E0Main oven sensor open or short-circuited.F3-E2Warming drawer sensor open or short-circuited.F31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.F5-E0Door and door switch mismatch (clean mode on some models).F6-E1Bake over-temperature condition.F6-E3Warming drawer over-temperature condition.Service modes (25)
- Auto Test1
- Code Display Mode["PD Models
- CONTROL RESETFrom diagnostic mode, scroll to step 6 'CONTROL RESET'.
- Cycle Credit["Enter Washer Diagnostic Mode (entire display flashing).","Press the PERM
- Diagnostic / Service ModePress CANCEL > CANCEL > START
- DISPLAYFrom diagnostic mode, scroll to step 5 'DISPLAY'.
- ENG MODE (Engineering Mode)From diagnostic mode, scroll to step 2 'ENG MODE'
- FAULTSFrom diagnostic mode, scroll to step 7 'FAULTS'
- Flashing Mode["PD Models
- Help Mode (dAS Mode)["Open the service door or insert a manual diagnostic card.","The message dAS will appear in the…
- Help Mode (PD Models)["Open the service door.","Press the WOOLENS button until the display reads 2.XX.","Press the PERM
- Manual Overview Test Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the WHITES button to start the…
- Quick Overview Test Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the WOOLENS button to start the…
- Quick Spin Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the COLORS button to start the…
- RELAY USAGEFrom diagnostic mode, scroll to step 8 'RELAY USAGE'.
- Service Access Code (No Console Removal)["Only functions on washers set up for 0 vend price without any Special Pricing set-up, and…
- Set-Up Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door."]
- Set-Up Mode (PR Models)["Install debit card reader per manufacturer's instructions.","Insert a set-up card (supplied by…
- Temperature CalibrationPress OPTIONS until 'Temp Calib' is displayed
- TEST MODEFrom diagnostic mode, scroll to step 3 'TEST MODE'.
- TEST ON (Relay Control)Available immediately upon entering diagnostic mode (CANCEL>CANCEL>START)
- USAGEFrom diagnostic mode, scroll to step 1 'USAGE'.
- VERSIONFrom diagnostic mode, scroll to step 4 'VERSION'.
- Washer Cleanout Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the BRIGHTS button to start the…
- Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (set-up mode).","Press and hold the DELICATES AND KNITS…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana air conditioner models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass