Amana C15F-C/P60240-3WC

Error codes (43)

Service modes (45)

• Code Display Mode["This mode can be accessed only when the washer is in error state.","Open the service door.","The…
• Code Display Sub-Mode["Open the service door when the washer is in an error state.","The current F code or d code will…
• Cycle Credit["Enter Flashing Mode (entire display flashing).","Press the HOT button (CC will display)."]
• Flashing Mode["PD Models
• Flashing Mode (Diagnostic Sub-Mode)["Open the service door.","Press and hold the COLD button until display segments are…
• Help Mode["Enter set-up mode.","Press the WARM button until set-up code 2.XX is on display.","Press the HOT…
• Help Mode (dAS mode)["Open the service door or insert a manual diagnostic card.","The message 'dAS' will appear on the…
• Help Mode (Manual Communication)["Enter set-up mode.","Press the WARM button until set-up code 2.XX is on display.","Press the HOT…
• Help Mode (PD models)["Open the service door.","Press the LOWER CENTER button until display shows 2.XX.","Press the…
• Help Mode (via dAS mode)["Enter set-up mode.","The message dAS will appear in the display.","Press the HOT button.","Press…
• Help Mode (via Manual Communication)["Enter set-up mode.","Press the WARM button until the set-up code 2.XX is on display.","Press the…
• Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press the COTTON/WHITES button."]
• Manual Overview Test Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the WHITES button to start the…
• P-01: Cancel Program, Error Reset, Clear Stored Credit["Enter Service Diagnostic Test Modes (steps 1-3).","Press START when 'P-01' is displayed."]
• P-02: Program Credit["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-02 using LOWER CENTER…
• P-03: Quick Overview Test Program["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-03 using LOWER CENTER…
• P-04: Manual Overview Test Program["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-04 using LOWER CENTER…
• P-05: Button Test["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-05 using LOWER CENTER…
• P-06: Drain and Spin["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-06 using LOWER CENTER…
• P-07: UI Diagnostics["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-07 using LOWER CENTER…
• P-08: Washer Clean Cycle["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-08 using LOWER CENTER…
• P-09: Factory Diagnostics["Enter Service Diagnostic Test Modes (steps 1-3).","Navigate to P-09 using LOWER CENTER…
• Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press the WARM button."]
• Quick Overview Test Cycle["Enter Washer Diagnostic Mode (entire display flashing).","Press the WOOLENS button to start the…
• Quick Spin Cycle["Enter Flashing Mode (entire display flashing).","Press the PERM PRESS button."]
• Service Access Code["If the washer is not in failure mode, the door must be opened to proceed.","Step 1
• Service Access Code (alternate setup entry without removing console)["If the washer is not in failure mode, open the door.","Press the upper left button.","Press the…
• Service Access Code (no console removal)["Open the door.","Press the upper left key pad.","Press the lower right key pad.","Press the upper…
• Service Access Code (PN Models - keyless entry)["Only functions on washers set up for 0 vend price without any Special Pricing, and Coin/Debit…
• Service Access Code (Technician Entry)["This method is only available on washers set for free operation (code 6 00).","Open the…
• Service Diagnostic Test Modes["Make sure power is turned off, then remove the service door on metercase models, or remove the…
• Service/Setup Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door.","The washer enters…
• Service/Setup Mode (PR Models via AA1 jumper)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1 connector on circuit…
• Set-Up Mode (9150 Models)["Insert access door key, turn, and lift to remove access door."]
• Set-Up Mode (9160 Models)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
• Set-Up Mode (PD Models)["Insert service access door key, turn, and lift to remove service access door."]
• Set-Up Mode (PR Models)["Install debit card reader per manufacturer's instructions.","Insert a set-up card (supplied by…
• Setup Mode["Insert access door key, turn, and lift to remove access door.","Alternatively, if a debit card…
• Setup Mode (PD Models)["Insert service access door key, turn, and lift to remove access door.","The washer enters set-up…
• Setup Mode (PN Models - AA1 method)["Unplug washer or disconnect power.","Open console, disconnect plug on AA1, close console.","Plug…
• Setup/Configuration Mode (PD models)["Insert the service door access key, turn and lift to remove the service access door."]
• Setup/Configuration Mode (PR models)["Insert the setup card (provided by card reader manufacturer) into the card reader.","If no setup…
• Washer Cleanout Cycle["Enter Flashing Mode (entire display flashing).","Press the COLORS/DELICATES button."]
• Washer Diagnostic Mode["First enter 'Start Operating Set-Up' (setup mode).","Press and hold the COLD button for 2 seconds…
• Washer Diagnostic Mode (Flashing Mode)["Enter Setup Mode (open service access door or insert set-up card).","Press and hold the COLD…

Full entry steps, exit procedures, and test sequences are available in Max.