mypros+
Model reference

Amana CD7/P60318-45W

Freezer

54 error codes11 service modes
MyPros+ Max

Diagnose your Amana CD7/P60318-45W.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (54)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory or control board, incompatible software components…10-1Dispenser electrical problem10-3Drying fan error2-1Control detected stuck key(s) in keypad or keypad connection.2-2User interface cannot communicate with main control3-1Open connector or component in Temperature Sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection or…3-3OWI (optical soil sensor) calibration failure.4-3Wash motor not running due to loose connection in Motor circuit and/or faulty…5-1Door stuck open5-2Door stuck closed6-1Inlet water low/no water (mechanical problem)6-2Inlet water fill valve electrical problem6-3Suds/air in pump6-4Float switch open6-6Incoming water cool6-7Water inlet6-8Regen valve electrical problem7-1No heat7-1 (flowmeter)Disconnected or damaged flowmeter.7-2Heater stuck on8-1Slow drain8-2Drain motor electrical problem8-3Drain8-5Drain stuck on9-1Diverter can't find position9-2Diverter stuck on9-3Diverter disk missingF0E0No error(s) found
View all 54 error codes
F1E0Internal failureF1E1Oven appliance manager failure (not applicable for lower oven on double oven…F2E0Keypad disconnected.F2E1Stuck key or shorted key.F2E2LED error on user interface.F2E3Keypad hardware failure.F3E0Upper oven temperature sensor open or shorted.F3E1Lower oven temperature sensor open or shorted.F3E2Warming drawer sensor shorted (oven not equipped with this feature).F3E3Meat probe sensor shorted.F5E0Door switch and latch switch do not agree.F5E1Door latch not operating.F6E0Lost communication (for microwave ovens only).F6E1Cook oven over temperature.F6E2Clean oven over temperature.F6E3Mini oven/warm drawer over temperature (not for built-in ovens).F6E4User interface/appliance manager mismatch.F6E5Cavity size is incorrect.F6E6Lost communication between UI and AM1.F6E7Lost communication between UI and AM2.F8E0Low fan speed underspeedF8E1Low fan speed overspeedF8E2High fan speed underspeedF8E3High fan speed overspeed

Service modes (11)

  • Buzzer Enable/DisablePress and hold the HI TEMP key for 3 seconds (a beep will sound).
  • Clear Customer Error HistoryDuring Service Diagnostics Cycle interval where Hi Temp LED is on (interval 22), press Hi Temp key…
  • Control LockPress and hold the Control Lock button for 5 seconds to activate or deactivate.
  • Customer Cycle Rapid AdvanceAfter starting a customer cycle, press HIGH TEMP
  • Customer Program Fast Forward ModeAfter starting a customer program, press HI TEMP
  • Demo Mode (Sales Display) DeactivationRun the service diagnostic program to deactivate demo mode.
  • diagnosticPress any one of the 3 keys 3 times within 8 seconds.
  • Diagnostics ModePress any 3 keys 3 times within 8 seconds
  • Rapid Advance Mode (Customer Cycles)After starting a customer cycle, press HIGH TEMP
  • Service Diagnostic Program1
  • Service Diagnostics Cycle1

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana freezer models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax