Model reference
Amana FS16
Freezer
37 error codes8 service modes
MyPros+ Max
Diagnose your Amana FS16.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (37)
CodeMeaning
CLOSE DOOR PRESS STARTThe machine door is open or the door lock microswitch, cables, or connectors…DOOR FAILThe door is not correctly closed or locked, or there is a failure in the door…DRAIN FAILUREDrain is clogged, drain valve is blocked or broken.E.0No errors reported by the frequency invertor.E.BEDefective invertor braking transistor error.E.ComDisconnected or defective communication between invertor and programmer.E.CPUCPU processor error in the frequency invertor.E.FAnInvertor fan has stopped (ventilation error).E.GFFault current goes through grounding; the invertor switches off (400V types…E.OC1Overcurrent during acceleration; current limit is exceeded.E.OC2Overcurrent during constant speed; current limit is exceeded.E.OC3Overcurrent during deceleration; current limit is exceeded.E.OHtExternal thermal relay is closed/disconnected.E.OLtInvertor current has reached the limit during constant speed; motor was stopped.E.Ov1Overvoltage in the direct circuit during acceleration.E.Ov2Overvoltage in the direct circuit during constant speed.E.Ov3Overvoltage in the direct circuit during deceleration.E.PEEEPROM memory error; CPU damaged (microprocessor).E.PUEParameter unit connector was disconnected from the invertor.E.rEtMaximum number of retry exceeded; operation could not be resumed within the set…E.rrSetting error; RESET signal is active, incorrect connection of parameter unit…E.THMElectronic thermal relay released; current over 100% but below 150% of given…E.THTElectronic thermal relay released; current over 150% of given power (motor…EEPROM FAILTemporary or permanent EEPROM memory error.FILL FAILWater filling failure due to low water pressure, clogged inlet valve filters…HEAT FAILHeating failure due to damaged contactor, steam valve, clogged steam sieve…INVERTOR/MOTOR FAULT XXXXA failure reported by the frequency invertor; the XXXX code indicates the…NO PROCESSA non-programmed washing cycle was selected and START key was pressed.OUT OF BALANCEIncorrect linen distribution, incorrect load, damaged machine (broken dampers…OVERLOAD FAULTThermally overloaded motor, damaged overcurrent relay, or damaged drain valve.View all 37 error codes
PAUSEA programmed pause has been entered in the wash cycle.PROCESS COMPLETE PLEASE WAITThe washing cycle is completing; displayed before the cycle fully ends.PROCESS MEMORY EXCEEDEDThe process memory contents have been exceeded during programming.SERVICE DUEThe number of completed wash cycles has reached the preselected service…TOO HOTThe temperature sensor recorded a temperature above 50°C at the moment the door…TOO HOT CHECK HEATINGThe temperature sensor recorded a temperature 15°C higher than the programmed…WATER IN CAGEThe drain valve is blocked, damaged, or drainage is clogged, causing water to…
Service modes (8)
- Cycle Counter Reset["1. Ensure display shows 'SELECT PROCESS
- Fault Delay Time Adjustment["1. Ensure display shows 'SELECT PROCESS
- Frequency Invertor Setup["1. Ensure display shows 'SELECT PROCESS
- Initialization Mode["1. Ensure display shows 'SELECT PROCESS
- Machine Type Selection (Pre-programmed Programmes)["1. Ensure display shows 'SELECT PROCESS
- Motor Current and Frequency Display (Frequency Controlled Machines)["1. Ensure display shows 'SELECT PROCESS
- Programming Mode["1. Ensure display shows 'SELECT PROCESS
- Software Version Display["1. Ensure display shows 'SELECT PROCESS
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana freezer models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass