mypros+
Model reference

Amana EPH02400-1B/P67220-10C

Furnace

26 error codes18 service modes
MyPros+ Max

Diagnose your Amana EPH02400-1B/P67220-10C.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (26)

CodeMeaning
DOOR OPENEither refrigerator or freezer door has been open for more than 3 minutes…F0E2Over suds condition detectedF0E4High water temperature detected during rinse cycleF0E5Off balance load detected.F1E1Main control fault.F1E2Motor control faultF2E1Stuck keyF2E3Mismatch of main control and UIF3E1Pressure sensor faultF3E2Inlet water temperature faultF5E1Lid switch faultF5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cyclesF7E1Basket speed sensor faultF7E5Shifter faultF7E6Motor faultF7E7Motor unable to reach target RPMF8E1Long fillF8E3Overflow conditionF8E5Hot and cold inlet hoses are reversed.F8E6No fillF9E1Long drainHIGH TEMPFreezer or refrigerator temperature has exceeded critical level (+15°F for…POWER UPAll temperature indicator lights flash after power is initially plugged in…THERMISTOR ALARMEither freezer or refrigerator thermistor circuit is open; freezer or…

Service modes (18)

  • Automatic Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until the 'Spin' LED is ON (all…
  • Calibration Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Clean Washer Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until…
  • Drain and Spin Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Forced Compressor Start (Electronic Testing Mode)["Press Display On pad to activate control panel.","Simultaneously press and hold Max Frz pad and…
  • Forced Defrost (from Program Mode B)["Enter Program Mode B.","Press and hold the Alarm Off pad for 3 seconds."]
  • Forced Defrost Start (Electronic Testing Mode)["Press Display On pad to activate control panel.","Simultaneously press and hold Max Ref and…
  • Forced Pulldown / Compressor Start (from Program Mode B)["Enter Program Mode B.","Press and hold Max Frz pad for 3 seconds."]
  • Manual Overview Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until FINAL…
  • Manual Test Mode["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' and 'Done' LEDs are…
  • Program Mode A (Thermistor Temperature Reading)["Open refrigerator door.","Press Display On pad.","Press * pad.","Within 6 seconds press the…
  • Program Mode B (Programming Functions)["Open refrigerator door.","Press Display On pad.","Press * pad.","Within 6 seconds press the…
  • Quick Overview Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Software Version Display Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until…
  • UI Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana furnace models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax