mypros+
Model reference

Amana CRCR-8-P85512-4S

Hood

47 error codes23 service modes
MyPros+ Max

Diagnose your Amana CRCR-8-P85512-4S.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (47)

CodeMeaning
d10/F31Overheating of motord11/F11Washer MCU errord12/F25Tachometer errord13Coin 2 errord14/F33Pump disconnectedd15/F34Load detected in washer during Washer Cleanout Cycle.d16Generation 2 debit card reader errord17/F22Door lock errord19/F29Door unlock errord2/F22Dryer exhaust thermistor open errord20/F28Communication failure between CCU and MCU.d21/F27Overflow conditiond22/F70Communication failure from CCU to UICd23/F70Washer communication failure between CCU and UIC.d23/F71Communication failure from UIC to CCUd24/F24Temperature sensor errord3/F23Dryer exhaust thermistor shorted errord3/F73Washer UIC failured3/F74Washer UIC failured4/F01Dryer motor control circuit errord4/F26Door switch errord5Coin 1 errord6/F01Washer CCU errord7/F20No water detected entering washerd8/F21Long draind8/F73UIC Microprocessor errord8/F74UIC EEPROM errord9Low voltage detection errorf01Dryer motor control circuit errorF11MCU error
View all 47 error codes
F20No water detected entering washerF21Long drainf22Exhaust thermistor open errorf23Exhaust thermistor shorted errorF24Temperature sensor errorF25Tachometer errorF26Door switch errorF27Overflow conditionsF28Communication failure between CCU and MCUF29Door unlock errorF31Overheating of motorF33Pump disconnectedF34Load detected in washer during Washer Cleanout Cycle.f70Communication failure from CCU to UICf71Communication failure from UIC to CCUf73UIC microprocessor errorf74UIC EEPROM error

Service modes (23)

  • Code Display Mode["Open the service door when the washer is in error state.","The current F code or d code will be…
  • Cycle Credit["Enter Flashing Mode (entire display flashing).","Press the HOT button (CC will display)."]
  • Diagnostic Mode["First enter Set-Up Mode (Start Operating Set-Up).","Press and hold the lower right (QUICK CYCLE)…
  • Dryer Field Diagnostic Cycle["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM
  • Dryer Field Diagnostic Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the upper middle (PERM
  • Help Mode["Press the lower left (PERM
  • Help Mode (DA Communication Established)["Open the service door.","The message dAS will appear in the display.","Press the HOT…
  • Help Mode (Manual Communication)["Open the service door.","Press the WARM button until the set-up code 2.XX is on display.","Press…
  • Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press the COTTON/WHITES button to start Manual…
  • Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press the WARM button to start Quick Overview…
  • Quick Spin Cycle["Enter Flashing Mode (entire display flashing).","Press the PERM PRESS button to start Quick Spin…
  • Set-up Mode["PD/PR Models
  • Setup Mode["Insert access door key, turn, and lift to remove access door.","Use HOT button to adjust values…
  • Washer Cleanout Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center right (BRIGHTS) button."]
  • Washer Cleanout Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center right (BRIGHTS) button."]
  • Washer Cycle Credit (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower left (PERM
  • Washer Diagnostic Mode (Flashing Mode)["Enter Start Operating Set-Up (open service door).","Press and hold the COLD button for 2 seconds…
  • Washer Manual Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center left (WHITES) button."]
  • Washer Manual Overview Test Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center left (WHITES) button."]
  • Washer Quick Overview Test Cycle["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (DELICATES AND KNITS)…
  • Washer Quick Overview Test Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the lower middle (DELICATES AND KNITS)…
  • Washer Quick Spin Cycle["Enter Diagnostic Mode (entire display flashing).","Press the center middle (COLORS) button."]
  • Washer Quick Spin Cycle (Diagnostic sub-mode)["Enter Diagnostic Mode (entire display flashing).","Press the center middle (COLORS) button."]

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana hood models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax