mypros+
Model reference

Amana APAC-140

HVAC

50 error codes11 service modes
MyPros+ Max

Diagnose your Amana APAC-140.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax

Error codes (50)

CodeMeaning
1-1Control detected K2 pilot relay stuck closed.1-2Damaged or corrupted memory on control board, or incompatible software…10-1Dispenser electrical problem; loose connection in dispenser circuit and/or open…10-2Vent wax motor electrical problem; loose connection in vent circuit and/or open…10-3Drying fan error; loose connection in fan circuit and/or open fan motor.2-1Stuck key(s) detected in keypad or keypad connection.2-2User interface cannot communicate with the main control board; incorrect…3-1Open connector or component in temperature sensing circuit; open or faulty…3-2Incoming water temperature above 167°F (75°C), or shorted connection/component…3-3OWI failed calibration.4-3Wash motor not running due to loose connection in wash motor circuit and/or…5-1Door stuck open; door was not latched within 3 seconds of pressing Start/Resume…5-2Door stuck closed; control programmed to not start if it suspects door switch…6-1Low/no water (mechanical problem); no water supply to dishwasher or various…6-2Fill valve electrical problem; loose connection in fill valve circuit and/or…6-3Suds/air in pump; too many suds, captured wash water, water leak, or missing…6-4Float switch open; overfill switch stuck in overfill position and/or dishwasher…6-7Disconnected or damaged flowmeter.6-8Regen valve electrical problem; loose connection in regen valve circuit and/or…7-1No heat; control programmed to disable heater but continue running cycles if it…7-2Heater stuck on; heater drive circuit on the control is faulty.8-1Slow drain; obstructed drain hose or path, or drain pump impeller fractured.8-2Drain motor electrical problem; loose connection in drain motor circuit and/or…8-3Drain stuck on; drain motor drive circuit on the control is faulty.9-1Can't find diverter position; corroded or loose connection in diverter…9-2Diverter stuck on; diverter drive circuit on the control is faulty.9-3Control detected diverter disk in sump is missing.9-4Lower spray arm error; mechanical blockage or jammed lower spray arm, or…F0E2Over suds condition detectedF0E4High water temperature detected during rinse cycle
View all 50 error codes
F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control faultF2E1Stuck keyF2E3Mismatch of main control and UIF3E1Pressure sensor faultF3E2Inlet water temperature faultF5E1Lid switch faultF5E2Lid lock faultF5E3Lid unlock faultF5E4Lid not opened between cyclesF7E1Basket speed sensor faultF7E5Shifter faultF7E6Motor faultF7E7Motor unable to reach target RPMF8E1Long fillF8E3Overflow conditionF8E5Hot and cold inlet hoses are reversed.F8E6No fillF9E1Long drain

Service modes (11)

  • Calibration Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Clean Washer Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until…
  • Drain and Spin Cycle["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Manual Overview Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until FINAL…
  • Quick Overview Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until only…
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","Place cycle selector…
  • Service Diagnostics CycleWhile in standby, press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3 with no more than 1 second…
  • Software Version Display Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until…
  • UI Test Mode["Activate Service Diagnostic Test Modes (steps 1 and 2).","Toggle cycle selector knob until RINSE…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana hvac models

75,000+ service documents · 20,000+ error codes · 100+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass · Plus applicable tax