mypros+
Model reference

Amana LC14EVP000

Microwave

8 documents67 error codes17 service modes

Available documentation

Tech Sheet

  • Tech Sheet - W11124916 - Rev B4 pg
    Covers this model
  • Tech Sheet - W11124904 - Rev B (EN,FR)4 pg
    Covers this model
  • Tech Sheet20 pg
    Covers this model
  • Tech Sheet - 8304550A (FR)12 pg
    Covers this model
  • TechSheet W11175370 REVA2 pg
    Covers this model
  • Tech Sheet16 pg
    Covers this model
  • Tech Sheet - W10200950 - Rev A8 pg
    Covers this model

Service Manual

  • Tech Manual104 pg
    Covers this model
MyPros+ Max

Diagnose your Amana LC14EVP000.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (67)

CodeMeaning
:Flashing colon indicates a power failure has occurred.CLrNo error(s) found.dLLid Lock FailuredULid Unlock FailureEnter clockPower failure has occurred; display flashes 'Enter clock' until CANCEL is…F 1Pressure Signal Out-of-RangeF 2Keypad/User Interface FailureF 40ATC Thermistor Open/ShortF 41Motor RPS Thermistor Open/ShortF 42Heater in unknown stateF 43Heater is continuously ONF 44Heater cannot be turned ONF 50Motor StalledF 51Motor RPS FailureF 52Motor Stop FailureF 53Motor Control OvertempF 54Motor Control OvercurrentF 72Basket Re-engagement FailureF0E0No fault (good condition)F1Control failure, UL A/D Error(s), BAKE/BROIL range over temperature.F1E0Oven user interface failure.F1E1Internal oven ACU (Appliance Control Unit) error.F1E4Microwave ACU PCBA failure.F1E5Microwave oven inverter error.F1E6Microwave generation error.F2Touch panel failure.F2E0Keypad disconnected.F2E1Stuck key failure on touch panel.F3Oven sensor opened or oven sensor shorted.F3E0Main oven sensor open or shorted.
View all 67 error codes
F3E1Lower main oven sensor shorted or open circuit.F3E2Warming drawer sensor shortedF3E3Meat probe connector jack or meat probe shorted.F4E1Cavity temperature sensor failure (FC NTC).F4E2Magnetron temperature sensor error.F4E4Humidity sensor error.F4E8Inverter over temperature.F4E9Inverter and magnetron over temperature.F5E0Door and latch switch do not agree.F5E1Latch not operating.F5E3Door and latch switch do not agree (lower oven).F5E4Latch not operating (lower oven).F6E0Oven user interfaceF6E1Over temperature.F6E2Clean oven over temperature.F6E3Mini oven/warm drawer over temperatureF6E4User interface/Appliance manager state status mismatch.F6E6Oven appliance managerF6E8Lost communications with microwave oven appliance manager.F6E9Oven appliance manager lost communication (lower oven).F7E0Water is not high enough or water did not boil fast enough.F8E0Product not wired correctly (cooling fan related).F8E1Low fan speed overspeed.F8E2High fan speed underspeed.F8E3High fan speed overspeed.F8E5Exhaust air temperature detection failure from Hood NTC.F9E0Product not wired correctly.HCHot, Cold ReversedLdLong DrainLFLong FilllidOpen/Close LidNTC OPEN, CALL FOR SERVICEHood NTC thermistor has an open circuit condition.NTC SHORT, CALL FOR SERVICEHood NTC thermistor has a short circuit condition.oLOverloadedPoPump OutSdSuds DetectionuLUnbalanced Load

Service modes (17)

  • Automatic Diagnostic Test Mode["Ensure washer is not currently running a cycle (in-progress screen should not be…
  • Console and Indicators Diagnostic Test Mode["Ensure washer is not currently running a cycle and LCD is on.","Press Power/Cancel button and…
  • diagnostic1. Plug in microwave oven or reconnect power, in idle mode, close the door, turn off hood light and…
  • Diagnostic Mode (Extended Mode)["Press OFF","Press OFF","Press START","Verify fault codes are displayed"]
  • Diagnostic Test Mode["Plug in microwave oven or reconnect power.","Press Cancel button to enter Standby mode (display…
  • Diagnostic/Test Mode1. Plug in microwave oven or reconnect power. In idle mode, close the door, turn off hood light and…
  • DiagnosticsPress LOWER OVEN > LOWER LIGHT > OVEN CANCEL, repeat this sequence 2 more times (3 times total)
  • Diagnostics Mode["Plug in microwave oven or reconnect power and press CANCEL to Standby (':')","Close door, then…
  • Diagnostics Mode - Double OvenPress UPPER OVEN > LOWER OVEN > LOWER LIGHT, then repeat this same 3-key sequence 2 more times…
  • Diagnostics Mode - Single OvenPress KITCHEN TIMER > TOOLS > SELF CLEAN, then repeat this same 3-key sequence 2 more times (total…
  • Manual Diagnostic Test Mode["Perform steps 1 and 2 of Activation of Automatic Diagnostic Test Mode (Sound and Display >…
  • Pressure Transducer Calibration["Enter Manual Diagnostic Test Mode.","From the Component Activation screen, select the 'Pressure'…
  • Programming Mode (After User Interface Replacement)["Disconnect oven power","Replace user interface","Reassemble panels before powering on","Reconnect…
  • Relay Activation Test["Enter diagnostic mode (OFF, OFF, START)","Press RELAY ACTIVATION","Select relay (BAKE, INNER…
  • Saved Fault Codes["Enter Service Mode (Sound and Display > Service Mode > 5, 6, 5, 6 within 5 seconds >…
  • Temperature AdjustmentPress and hold BAKE key for 5 seconds
  • Touch Panel and PCBA Self-Diagnostic Test Mode["Press and hold the STOP/CLEAR button while opening the door.","While still holding the STOP/CLEAR…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass