Model reference
Amana ML-40/P76804-2M
Microwave
8 documents73 error codes21 service modes
Available documentation
Tech Sheet
- Tech Sheet - 395766116 pg
- Tech Sheet2 pg
- Tech Sheet - W10176957 - Rev B16 pg
- Tech Sheet W1013349016 pg
- tech sheet w11332389 revb2 pg
- Tech Sheet 8183018 Rev B16 pg
- Technical Service Sheet 8183018 Revision B16 pg
Installation Guide
- Installation Instructions45 pg
MyPros+ Max
Diagnose your Amana ML-40/P76804-2M.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (73)
CodeMeaning
F/01No water detected entering machine or pressure switch trip not detected after…F/02Long drainF/05Water temperature sensor (NTC) value is out of range during the water heating…F/06Drive motor tachometer errorF/07Motor Control Unit (MCU) errorF/09Overflow conditionF/10MCU heat sink thermal tripF/11Serial communication errorF/13Dispenser circuit errorF/14EEPROM errorF/15Motor Control Unit (MCU) errorF/21CCU/Touch-pad/LED assembly errorF/22Pressure switch failureF/23System leakF/24Door unlock errorF/25Door lock errorF01EEPROM communication error between the Central Control Unit (CCU) and the…F02Pump drive errorF03Main relays errorF04Heater short circuit to groundF05Steamer defectF06Motor Control Unit (MCU) errorF07Heater short circuit to groundF08No water detected entering machine or pressure switch trip not detectedF09No water detected entering machine or pressure switch trip not detectedF10No water detected entering machine or pressure switch trip not detectedF11No water detected entering washer or pressure switch trip not detectedF1E4MW relay failure.F21Long drainF22Door lock errorView all 73 error codes
F23Heater failureF24Water temperature sensor errorF25Drive motor tachometer errorF26Door switch errorF26EDispenser system errorF27Overflow conditionF28Serial communication error between the CCU and the MCU.F29Door unlock errorF2E1Touch panel failure.F30Dispenser system errorF31Motor Control Unit (MCU) failureF32Pressure switch failureF33Analog pressure sensor failureF34Motor Control Unit failureF35Steamer communication failureF36Steamer electronic board relays errorF37Total steamer failureF38Steamer inlet valve failureF39Steamer time out reachedF40Central Control Unit heartbeat failureF41User Interface heartbeat failureF42Not supportedF43Steamer inlet valve failureF44Steamer time out reachedF45Central Control Unit heartbeat failureF46User Interface heartbeat failureF47Not supportedF48Steamer inlet valve failureF49Steamer time out reachedF4E3Exhaust air temperature detection failure.F50Central Control Unit heartbeat failureF51User Interface heartbeat failureF53Not supportedF60Central Control Unit heartbeat failureF61User Interface heartbeat failureF70Not supportedF8E5Exhaust air temperature detection failure.F9E3Cavity light / Cooling fan relay failure (only occurs in Diagnostics).FDE2Turntable relay failure (only occurs in Diagnostics).FDE3Exhaust fan relay failure (only occurs in Diagnostics).rLUnload indicationSdSuds lockSudSuds lock
Service modes (21)
- Automatic Diagnostic Test (Quick Entry)1
- diagnostic1
- Diagnostic Test["Washer must be empty and control must be in OFF state.","Close the door.","Under Cycles, press…
- Diagnostic Test (Full - with error history and software versions)Press and hold a button for 2-5 seconds, then release
- Diagnostic Test (with error history)["Close the door.","Press and hold any one button for 2-5 seconds, then release.","Press and hold…
- Diagnostic Test Only["Execute with an empty drum.","Close the door.","Push power.","Select the Drain and Spin…
- Diagnostic Test Only (automated test without error history)1
- Diagnostic Test Only (Quick Start)1
- Diagnostic Test with Error History and SW Versions["Washer must be empty and control must be in OFF state.","Close the door.","Select any one key…
- diagnostic_test_only1
- Display Last Stored Failure Code["Under Cycles, press DRAIN/SPIN.","Press SPIN SPEED and select NO SPIN.","Under Options, press and…
- Error History, Software Versions and Diagnostic Test1. Washer must be empty and control must be in OFF state. 2. Close the door. 3. Select any one key…
- Full Diagnostic (Error History, Software Versions, and Diagnostic Test)["Washer must be empty and control in OFF state.","Close the door.","Select any one key except…
- Manual Diagnostic Test["Washer must be empty and control in OFF state.","Close the door.","Select any one key except…
- Monthly Maintenance/Cleaning Cycle["Open washer door and remove all items; close door.","Open dispenser drawer and remove detergent…
- Quick Diagnostic Test (Automated Test Only)1
- Quick Diagnostic Test (Automatic Test Only)["Drum must be empty.","Close the door.","Push power.","Select the Drain and Spin…
- Service Mode (Error Code Recall and Diagnostic)1. Select any one key (except PAUSE/CANCEL). 2. Using the same key
- Steamer Functionality CheckupClose the door
- steamer_functionality_checkup1
- Touch Panel and ACU Test (Diagnostics mode)["Plug in microwave oven or reconnect power.","In idle mode, close the door, turn off hood light…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana microwave models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass