Model reference
Amana RC-14B
Microwave
41 error codes10 service modes
MyPros+ Max
Diagnose your Amana RC-14B.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (41)
CodeMeaning
F0E1Load detected in drum during Clean Washer cycle.F0E2Excessive suds detected in washer; washer is running a suds reduction routine.F0E4High temperature error during wash cycle.F0E5Off balance load detected.f1 e1Primary control failure.F12E0Communication between the Human Machine Interface and Wi-Fi Module has not been…F1E1Primary control failure.F1E2MCU over- or under-voltage error.f2 e1Stuck button or user interface mismatch (only appears in service diagnostic…F2E1Stuck button or user interface mismatch (keypad/user interface failure)f3 e1Exhaust thermistor is open.f3 e2Exhaust thermistor has shorted.f3 e6Moisture sensor strip is open (only appears in service diagnostic mode).f3 e7Moisture sensor strip has shorted (only appears in service diagnostic mode).F3E1Exhaust thermistor is open.F3E2Exhaust thermistor has shorted.F3E5Dry NTC open circuit fault; dry temperature sensor out of range, open circuit…F3E6Moisture sensor strip is openF3E7Moisture sensor strip has shortedF4E1Wash heater relay error or no feedback signal; ACU cannot detect temperature…F4E2Wash heater relay error.F4E4Blower error.F5E2Door lock failure.F5E3Door unlock failure.F5E4Door not open error.F6E1No communication from the HMI detected by ACU.F6E2No communication from the ACU detected by the HMI.F6E3No communication from the MCU detected by the ACU.F7E10Motor disconnected error.F7E12MC/MCU overload.View all 41 error codes
F7E2MC/MCU over temperature error or over current error/internal failure.F7E8MC/Motor over temperature error.F7E9Motor will not turn (locked rotor).F7EAMotor disconnected error (alternate display of F7E10).F7ECMC/MCU overload (alternate display of F7E12).f8 e1No voltage detected at the water valve relay (steam models only, only appears…F8E1No voltage detected at the water valve relay (steam models only)F8E3Overflow condition detected.F9E1Long drain time detected.FCE0Communication between the Human Machine Interface and Wi-Fi Module has not been…pfPower failure occurred while the dryer was running.
Service modes (10)
- Clear Error History["Enter Service Diagnostic Mode.","From the DIAGNOSTICS HOME screen, press CLEAR ERROR HISTORY…
- Component Activation (Manual)["Enter Service Diagnostic Mode (see entry procedure above).","From DIAGNOSTICS HOME screen, press…
- Customer-Focused Drying Mode Adjustment["Ensure dryer is in standby mode.","Press and hold the TEMP button for more than 6…
- Fault/Error Code Display["Enter Service Diagnostic Mode.","From the DIAGNOSTICS HOME screen, press ERROR DIAGNOSTIC…
- Human-Machine Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
- Quick Diagnostic Test["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
- Quick Service Cycle["Enter Service Diagnostic Mode.","From DIAGNOSTICS HOME, press Component Activation.","Select…
- Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off, or with only DONE or…
- Software Version Display["Enter Service Diagnostic Mode.","From DIAGNOSTICS HOME, press System Info.","Select Software…
- User Interface/Control System Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana microwave models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass