Model reference
Amana RMC-20C/P76230-1M
Microwave
4 documents46 error codes28 service modes
Available documentation
Tech Sheet
- tech-sheet-W10589610-RevA.pdf32 pg
- Tech Sheet 8563818 Rev A16 pg
Tech Tip
- Instruction Sheet2 pg
Installation Guide
- Installation Instructions34 pg
MyPros+ Max
Diagnose your Amana RMC-20C/P76230-1M.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (46)
CodeMeaning
AFRestricted airflow detected that may affect dryer performance.d13The Coin 2 sensor is detected as blocked; coin vault may be full of money, or…d16Gen 2 Debit Card Reader Errord5The Coin 1 sensor is detected as blocked; coin vault may be full of money, or…d9Low voltageE1Thermistor is open.E2Thermistor has shorted.E3User interface or software mismatchf01CCU (Central Control Unit) errorF03Main control detects an out of range pressure signal from the pressure…F07Main control cannot determine position of shifter (shifter system failure).f11MCU (Motor Control Unit) has a failure, possibly due to repeating under or…F1E1Motor relay stuck on, indicates an ACU problem.F1E3Incorrect controller installed (electric models only); ACU and/or UI part…f20No water detected entering washerf21Long drainf22Door lock errorf24Temperature sensor errorf25Tachometer errorf26Door switch errorf27Overflow conditionsf28Communication failure between CCU and MCU.f29Door unlock errorF2E1User Interface stuck button (depressed for over 20 seconds); only appears in…F2E4UI Software ErrorF2E5UI Software Errorf31Overheating of motorF32No fillf33Pump disconnectedf34Load detected in washer during Washer Cleanout Cycle.View all 46 error codes
F3E1Exhaust thermistor is open or shortedF3E2Moisture sensor strip is open or shorted; only appears in service diagnostic…F3E3Inlet thermistor is open or shortedF4E1Heater 1 failure or connector problem; no voltage detected at the heater relay.F4E2Heater 2 failure or connector problem (electric models only); no voltage…F4E3Restricted airflow that may affect dryer performance.F4E4L2 line voltage error (less than 50 V detected at the ACU), electric models…F6E2Communication errorF6E3Communication errorf70Communication failure between CCU and UI (User Interface).F71Communication failure between CCU and UIf73UI (User Interface) failuref74UI (User Interface) failureF77Off balance load detected.L2Low L2 voltage (less than 30 V) detected at the CCU.PFPower failure occurred while the dryer was running.
Service modes (28)
- Adjusting Customer-Focused Dryness LevelIn standby mode (dryer plugged in but not powered up), press and hold the DRYNESS button for…
- Console Diagnostics - Switches and Indicators["Enter diagnostic test mode (see above).","Press each button or turn the cycle selector to each…
- Console Diagnostics (within Diagnostic Test Mode)["Enter the Diagnostic Test Mode as described above.","Press each button or turn the cycle selector…
- Diagnostic - Door Switch["Enter diagnostic test mode.","Open the door
- Diagnostic - Moisture Sensor["Enter diagnostic test mode.","Locate two metal strips on the face of the lint screen…
- Diagnostic Test Mode["Ensure the dryer is in standby mode (plugged in and all indicators off).","Within 5 seconds…
- Door Switch Diagnostic (within Diagnostic Test Mode)["Enter the Diagnostic Test Mode.","Open the door
- Help Mode["1
- Key Activation & Encoder TestFrom Service Diagnostic Mode, press and release the 1st button used to activate Service Diagnostic…
- Manual Overview Test["Enter Flashing Mode (entire display flashing).","Press COTTON/WHITES button to start Manual…
- Moisture Sensor Diagnostic (within Diagnostic Test Mode)["Enter the Diagnostic Test Mode.","Locate two metal strips on the face of the lint screen…
- P-01 Clear Errors["Access Service Diagnostic Test Modes.","Press START after 'P-01' is displayed to clear an active…
- P-02 Cycle Credit["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-02'.","Press START…
- P-03 Service Diagnostic["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-03'.","Press START…
- P-04 Manual Diagnostic["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-04'.","Press START…
- P-05 Calibration Cycle["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-05'.","Press START…
- P-07 UI Diagnostics["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-07'.","Press START…
- P-09 Tachometer Verification["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-09'.","Press START…
- P-12 Clean Washer Cycle["Access Service Diagnostic Test Modes.","Press Normal key pad to step to 'P-12'.","Press START…
- Quick Overview Test["Enter Flashing Mode (entire display flashing).","Press WARM button to start Quick Overview Test."]
- Service Access Code (keypad entry without removing console)["Washer must be set for 0 vend price, no Special Pricing, and Coin/Debit Option set to 'J._d'. If…
- Service Diagnostic Mode1
- Service Diagnostic Test Modes (entry)["1
- Service Test ModeFrom Service Diagnostic Mode, press and release the 2nd button used to activate Service Diagnostic…
- Setup Mode (via service access door)["Insert access door key, turn, and lift to remove access door.","Alternatively, if a debit card…
- Software Version DisplayFrom Service Diagnostic Mode, press and hold the 2nd button used to activate Service Diagnostic…
- Technician Service Access Code (free vend models only)["This method is only available on washers set to free vend (6 00).","Press the LEFT UPPER, RIGHT…
- Washer Diagnostic Mode (Flashing Mode)["First enter 'Start Operating Set-Up' (open service access door).","Press and hold the COLD button…
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana microwave models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass