mypros+
Model reference

Amana RRL-10C

Microwave

3 documents24 error codes25 service modes

Available documentation

Tech Sheet

  • techsheet-12074204.pdf30 pg
    Covers this model
  • techsheet w10280489 revd48 pg
    Covers this model

Installation Guide

  • Installation Instructions6 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RRL-10C.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (24)

CodeMeaning
DOOR OPENEither refrigerator or freezer door has been open for more than 3 minutes…F0E0No fault detected.F0E2Over suds condition detected; suds prevent basket from spinning up to speed or…F0E4High water temperature detected (105°F or higher) during rinse cycle.F0E5Off balance load detected.F1E1Main control fault.F1E2Motor control fault on the main control board.F2E1Stuck key; one or more keys on the User Interface were actuated for 15…F2E3Mismatch of main control and User Interface; UI identification does not match…F3E1Pressure sensor fault; main control detects an out of range pressure signal.F3E2Inlet water temperature fault; inlet thermistor detected to be open or shorted.F5E1Lid switch fault; lid is in locked state but lid switch is open.F5E2Lid lock fault; lid lock has not moved into locked position or motor cannot be…F5E3Lid unlock fault; lid lock has not moved into unlocked position or motor cannot…F5E4Lid not opened between cycles; user presses START after several consecutive…F7E1Basket speed sensor fault; main control cannot determine speed of basket or…F7E5Shifter fault; main control cannot determine position of shifter.F7E6Motor fault; open clockwise or counterclockwise circuit of the motor.F7E7Motor unable to reach target RPM; basket speed sensor detects that target RPM…F8E1No fill or long fill; water level does not change for a period of time or water…F8E3Overflow condition; main control senses water level that exceeds the washer's…F8E5Hot and cold inlet hoses are reversed.F9E1Long drain; water level does not change after the drain pump is on for 10…HIGH TEMPFreezer or refrigerator temperature has exceeded critical level (+15°F for…

Service modes (25)

  • Actuator and Switch Test["Set TEMP SELECT switch to Hot/Cold (HC).","Unplug the washer power cord from the household outlet…
  • Automatic Operations Test["Set TEMP SELECT switch to Cold/Cold (CC).","Unplug the washer power cord from the household…
  • Automatic Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • automatic_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Spin' LED is…
  • calibration["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Rinse' LED is…
  • Calibration Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • diagnostic (service diagnostic test modes entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Electronic Testing Mode - Forced Compressor Start["Press Display On pad to activate control panel.","Simultaneously press and hold Max Frz pad and…
  • Electronic Testing Mode - Forced Defrost Start["Press Display On pad to activate control panel.","Simultaneously press and hold Max Ref and…
  • Fault Code Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • fault_code_display["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until only the 'Done' LED is…
  • Interface Test["Set TEMP SELECT switch to Warm/Warm (WW).","Unplug the washer power cord from the household…
  • Manual Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • manual_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Spin' and 'Done' LEDs are…
  • Program Mode A (Thermistor Temperature Reading)["Open refrigerator door.","Press Display On pad.","Press * pad.","Within 6 seconds press the…
  • Program Mode B - Forced Defrost["Enter Program Mode B.","Press and hold the Alarm Off pad for 3 seconds."]
  • Program Mode B - Forced Pulldown (Compressor Start)["Enter Program Mode B.","Press and hold Max Frz pad for 3 seconds."]
  • Program Mode B (Programming Functions)["Enter Program Mode A first (see above).","Toggle to Program Mode B by pressing Display On pad
  • Service Diagnostic Test Modes (Entry)["Ensure washer is in standby mode (plugged in with all indicators off).","RESET
  • Software Version Display Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • sw_version_display["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse', 'Spin', and 'Done'…
  • Tachometer Verification Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • tachometer_verification["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Wash' and 'Done' LEDs are…
  • UI Test Mode["Activate Service Diagnostic Test Modes.","Turn cycle selector knob until status LEDs show
  • ui_test["Enter Service Diagnostic Test Modes.","Turn cycle selector knob until 'Rinse' and 'Spin' LEDs are…

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass