mypros+
Model reference

Amana RV-8/P75260-4M

Microwave

4 documents63 error codes26 service modes

Available documentation

Service Manual

  • Service Manual - Countertop Domestic Toast and Bake Microwaves34 pg
    Covers this model
  • Service Manual for Countertop Domestic Microwave Ovens50 pg
    Covers this model
  • Service Manual - 2001-2003 Countertop Domestic Microwave Ovens50 pg
    Covers this model

Tech Sheet

  • Tech Sheet - W11467195 - Rev B24 pg
    Covers this model
MyPros+ Max

Diagnose your Amana RV-8/P75260-4M.

  • Step-by-step diagnostics from the service manual
  • Test values, resistance specs, and wiring references
  • Verified part numbers when replacement is needed
Start diagnosing

$29/month · Cancel anytime · Or $9.95 3-day pass

Error codes (63)

CodeMeaning
AFLow airflow detected that may affect dryer performance.ErrExcess setting time (Bake/Broil/Top BrownErr 1Temperature sensor is open.Err 2Temperature sensor is shorted.Err 3Sensor has detected that the lower heater has not been in horizontal position…F0 E7Low Voltage ErrorF1 E1ACU (Appliance Control Unit) fault detected.F1 E4UIC (User Interface Control) fault detected.F1 E7Voltage input fault detected.F1E1Motor relay stuck on, indicates an ACU problem.F1E3Incorrect controller installed; ACU and/or User Interface part numbers do not…F1E5ACU parameter file missing; parameter memory invalid.F2 E1Dryer keypad stuck errorF2 E2Upper Dryer Keypad Stuck ErrorF2E1User Interface stuck button (depressed for over 20 seconds); only appears in…F2E2User Interface software errorF2E3UI and ACU model ID parameter mismatch caused by replacement of either UI or…F2E4UI software errorF2E5UI software errorF3E1Exhaust thermistor is open or shorted; open if temperature drops below 18°F…F3E2Moisture sensor strip is open or shorted; only appears in service diagnostic…F3E3Inlet thermistor is open (temperature below 18°F / >245k ohms) or shorted…F3E4Inlet thermistor has shorted; temperature above 391°F (<328 ohms).F3E5Inlet and exhaust thermistors are both open; will occur if P14 connector is not…F3E6Moisture sensor strip is open; this fault code will only appear when in the…F3E7Rear moisture sensor strip is open or shorted (Maytag models only); only…F4E1Heater 1 failure or connector problem; no voltage detected at the heater relay.F4E2Heater 2 failure or connector problem (electric models only); no voltage…F4E3Restricted airflow; low airflow that may affect dryer performance.F4E4L2 line voltage error; low L2 voltage (less than 50V) detected at the ACU.
View all 63 error codes
F4E5High limit exceeded; temperature threshold of the dryer has been exceeded…F5 E1Dryer door circuit error.F5 E6Upper Dryer Door Circuit ErrorF6 E1Communication failure between ACU and UICF6E1Communication error from UI to CCU; communication between the CCU and UI has…F6E2Communication errorF6E3Communication errorF7 E6Lower Dryer Motor Circuit ErrorF7 E7Upper Dryer Motor Circuit ErrorF7 E8Lower Dryer Motor Sense ErrorF7 E9Upper Dryer Motor Sense ErrorFC E1Model/Serial number not programmed.FC E2Model/Serial number not matching between ACU and UIC.FC E3Wi-Fi connection fault.FC E4USB stick failure (USB full, not detected, or not accessible).FC E5Software update failureFC E6Model setup export failureFC E7Model setup import failureFC E8Wi-Fi module not responding or not connected.FCE0Communication error between ECM and CCU (model WEL98 only).FCE1Communication error from dryer to wireless router (model WEL98 only).FCE2Wireless router cannot communicate with the internet (model WEL98 only).FCE3Antenna A (J2) is bad (model WEL98 only).FCE4Antenna B (J11) is bad (model WEL98 only).FCE5Current Transformer A not functioning at J12 (model WEL98 only).FCE6Current Transformer B not functioning at J12 (model WEL98 only).FCE7Provisioning failureFP E1Coin 1 circuit error.FP E2Coin 2 circuit error.FP E3Card reader communication error.LLow L2 voltage (less than 50V) detected at the CCU; displayed on models 4000…L2Low L2 voltage (less than 50V) detected at the CCU.PFA power failure occurred while the dryer was running.

Service modes (26)

  • child_lockPress STOP/CLEAR pad, then press and hold 0 until 'L' or 'LOCKED' appears in the display and two…
  • Customer-Focused Dryness Level Adjustment["In standby mode (dryer plugged in but not powered up), press and hold the DRYNESS or DRY LEVEL…
  • demoPress CONTROL SET-UP pad, then press number pad 5, then press option 1 to enable Demo mode.
  • Diagnostic Mode (Field Diagnostic Cycle)["Enter Setup Mode first.","Navigate to set-up code 6 or 7 (or while dAS displays if operating with…
  • diagnostic_modePress DELICATES keypad for one second while in any of the set-up codes 1 through 6 (or while dAS…
  • Fault Code Display and Clear["Activate Service Diagnostic Mode first.","Press and release the 3rd button to display saved fault…
  • Help Mode["Enter Setup Mode first.","Navigate to set-up option 2.XX (or while dAS displays if operating with…
  • help_modePress HEAVY DUTY keypad while in special pricing option step 2.XX (or while dAS displays if…
  • Install Diagnostics["First activate Service Diagnostic Mode.","Press and release the 2nd button used to activate…
  • Key Activation & Encoder Test["Enter Service Diagnostic Mode first.","Press and release the 1st button used to activate Service…
  • Loads Test Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Within 5 seconds: Press…
  • model_serial_number_menuEnter Help Mode first
  • Model/Serial Number Menu["Enter Help Mode.","While on the S0 screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • Quick Diagnostic TestFrom Service Diagnostics, navigate to Error Diagnostic > Quick Diagnostic Test
  • Service Diagnostic Mode["Ensure dryer is in standby mode (plugged in with all indicators off).","Select any three buttons…
  • Service Diagnostics1. Ensure dryer is in standby mode (plugged in with all indicators off). 2. Select any three…
  • Service Test Mode["Enter Service Diagnostic Mode first.","Press and release the 2nd button used to activate Service…
  • Setup Mode (Control Set-Up)["PD Models
  • setup_modeCOIN Models
  • Software Version Display["Enter Service Diagnostic Mode first.","Press and hold the 2nd button used to activate Service…
  • UI Component TestFrom Service Diagnostics, navigate to Component Activation > UI Component Test
  • USB Menu["Enter Help Mode.","While on the USB screen, press the HEAVY DUTY key.","Use NORMAL key to advance…
  • usb_menuEnter Help Mode first
  • User Interface Test["First activate Service Diagnostic Mode.","Press and release the 1st button used to activate…
  • User Interface/Control System Test["Activate Service Diagnostic Mode first.","Press and release the 1st button used to activate…
  • wifi_menuWhile in setup mode on the F0 screen, press the HEAVY DUTY keypad to enter Wi-Fi mode.

Full entry steps, exit procedures, and test sequences are available in Max.

Related Amana microwave models

78,000+ service manuals · 160,000+ error codes · 55+ brands

Get Started

$29/month · Cancel anytime · Or $9.95 3-day pass