Model reference
Amana RCC-4-A/P72778-1MA
Oven
9 documents36 error codes11 service modes
Available documentation
Service Manual
- ADC AD-320 ServiceManual-ADG-330D,ADG-320D-DMC-24VAC-PH5 PastProduction OPL53 pg
- ADC AD-200 ServiceManual-Tilt PastProduction OPL107 pg
- ADC AD-200 ServiceManual-NonTilt-1993-thru-1998 PastProduction OPL82 pg
- jobaid 4317323 kac 2860 pg
- Technical Education Job Aid 4317323 KAC-28 Electric Built-in Single Oven60 pg
Tech Sheet
- Tech Sheet - 1602292915 pg
Installation Guide
- Installation Instructions32 pg
- Installation Instructions7 pg
- Instruction Sheet1 pg
MyPros+ Max
Diagnose your Amana RCC-4-A/P72778-1MA.
- Step-by-step diagnostics from the service manual
- Test values, resistance specs, and wiring references
- Verified part numbers when replacement is needed
Start diagnosing
$29/month · Cancel anytime · Or $9.95 3-day pass
Error codes (36)
CodeMeaning
donEDrying and cooling cycles complete, or dryer is in the anti-wrinkle cycle.doorSafety circuit faultdSFLDryer sensor circuit failureF0Default F codeF1Electronic control malfunction (all E codes).F1-E0Key held down too long, or key is shorted.F1-E1Keypad keytail not connected.F1-E5Cancel key drive line open.F2Electronic control malfunction.F2 E0Key held down too long, or key is shorted.F2 E1Keypad keytail not connected.F2 E5Cancel key drive line open.F3 E0Temperature sensor opened.F3 E1Temperature sensor shorted.F3 E2Oven temperature too high (over 301°C / 575°F in Cook mode).F3 E3Oven temperature too high (over 510°C / 950°F in Clean mode).F3-E0Temperature sensor opened.F3-E1Temperature sensor shorted.F3-E2Oven temp too high (over 301°C [575°F] in Cook mode).F3-E3Oven temp too high (over 510°C [950°F] in Clean mode).F4 E1Meat probe malfunctionF4-E1Meat probe malfunctionF5 E0Door is open but latch is locked (door switch closed indicating open door, and…F5 E1Self-clean latch will not lock.F5 E5Self-clean temperature (288°C / 550°F) not reached within 45 minutes.F5 E7Self-clean latch will not unlock.F5-E0Door is open, but latch is locked (door switch closed indicating open door, and…F5-E1Self clean latch will not lock.F5-E5Self clean temperature (288°C [550°F]) not reached within 45 minutes.F5-E7Self clean latch will not unlock.Service modes (11)
- Automatic Review Mode (PLOC)["Access programming mode via the Program Switch (PS).","Navigate to PLOC (Program Location…
- DSI Module Lock-Out ResetWhen DSI module is in LOCK-OUT mode (red LED stays on continuously), open and close the main door…
- Fahrenheit to Celsius conversionPress the BROIL pad for 5 seconds
- Fault code history recallPress and hold the '0' touchpad for 5 seconds to access the previous fault codes
- Phase 5 DMC Programming ModeAccess via the Program Switch (PS); close and open the Program Switch to enter programming
- Phase 5 DMC System DiagnosticsAll major circuits including door, lint drawer, microprocessor temperature sensor, heat and motor…
- Phase 5 Microprocessor Hot ResetWhen display reads 'Hot', wait for temperature to drop below 220°F (104°C), then press the…
- Programming Cavity SizeWithin 60 seconds of power up, press
- Programming Mode (Program Switch)["Close the Program Switch (PS) located on the DMC computer to enter programming mode.","Use…
- Programming the cavity sizeWithin 60 seconds of power up, press the following touchpads in order
- Sabbath Mode exitIf 'SAB' appears in the display, press and hold the '6' touchpad for 5 seconds to end Sabbath Mode.
Full entry steps, exit procedures, and test sequences are available in Max.
Related Amana oven models
78,000+ service manuals · 160,000+ error codes · 55+ brands
Get Started$29/month · Cancel anytime · Or $9.95 3-day pass